Commit Graph

4185 Commits

Author SHA1 Message Date
Tianling Shen
be24475d5c
Revert "ath79: append/prepad okli kernel support"
This patch is for CSAC support. As it was dropped, this can go too.

This reverts commit ce6fd478a3.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 6cffc4a15e)
2022-04-18 03:45:49 +08:00
Moritz Warning
59fbceb2d0 treewide: use uniform vendor value for british telecom
British Telecom is mostly known as BT.

Signed-off-by: Moritz Warning <moritzwarning@web.de>
2022-04-16 23:38:32 +08:00
Sungbo Eo
3c2a0a499e ramips: add support for ipTIME T5004
ipTIME T5004 is a 5-port Gigabit Ethernet router, based on MediaTek MT7621A.

Specifications:
* SoC: MT7621AT
* RAM: 128 MiB
* Flash: NAND 128 MiB
* Ethernet: 5x 1GbE
  * Switch: SoC built-in
* UART: J4 (57600 baud)
  * Pinout: [3V3] (TXD) (RXD) (GND)

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware via recovery mode:
1.  Press reset button, power up the device, wait >15s for CPU LED
    to stop blinking.
2.  Upload stock image to TFTP server at 192.168.0.1.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-04-16 23:29:49 +08:00
WonJung Kim
ddf3eb8beb ramips: add support for ipTIME A3004T
ipTIME A3004T is a 2.4/5GHz band router, based on Mediatek MT7621.

Specifications:
 - SoC: MT7621 (880MHz)
 - RAM: DDR3 256M
 - Flash: NAND 128MB  (Macronix NAND 128MiB 3,3V 8-bit)
 - WiFi:
   - 2.4GHz: MT7615E
   - 5GHz : MT7615E
 - Ethernet:
   - 4x LAN
   - 1x WAN
 - USB: 1 * USB3.0 port
 - UART:
   - 3.3V, TX, RX, GND / 57600 8N1

Installation via web interface:
 1. Flash initramfs image using OEM's Recovery mode
 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
 - Flash stock firmware via OEM's Recovery mode

How to use OEM's Recovery mode:
 1. Power up with holding down the reset key until CPU LED stop blinking.
 2. Set fixed ip with `192.168.0.2` with subnet mask `255.255.255.0`
 3. Flash image via tftp to `192.168.0.1`

Additional Notes:
 This router shares one MT7915E chip for both 2.4Ghz/5Ghz.
 radio0 will not working on 5Ghz as it's not connected to the antenna.

Signed-off-by: WonJung Kim <git@won-jung.kim>
(added led dt-bindings)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-04-16 23:26:56 +08:00
Sungbo Eo
477afbaf53 ramips: add support for WeVO AIR DUO
WeVO AIR DUO is a 1-bay NAS & 802.11ac (Wi-Fi 5) router, based on
MediaTek MT7620A.

Specifications:
* SoC: MT7620A
* RAM: 64 MiB
* Flash: SPI NOR 16 MiB
* USB & SATA bridge controller: JMicron JMS567
  * SATA 6Gb/s: 2.5" drive slot
  * USB 3.0: Micro-B
  * USB 2.0: connected to SoC
* Wi-Fi:
  * 2.4 GHz: SoC built-in
  * 5 GHz: MT7612EN
* Ethernet: 5x 1GbE
  * Switch: MT7530WU
* UART: 4-pin 1.27 mm pitch through-hole (57600 baud)
  * Pinout: (3V3)|(RXD) (TXD) (GND)

Notes:
* The drive is accessible through the external USB port only when the
  router is turned off.

Installation via web interface:
1.  Flash **initramfs** image through the stock web interface.
    The image filename should have ".upload" extension.
2.  Boot into OpenWrt and perform sysupgrade with sysupgrade image.

Revert to stock firmware:
1.  Perform sysupgrade with stock image.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-04-16 23:23:13 +08:00
Tianling Shen
8733f18948
x86/zen: drop broken target
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-04-14 10:36:35 +08:00
AmadeusGhost
233d89378a Merge Mainline 2022-04-08 11:35:35 +08:00
AmadeusGhost
694ba4ef78 sunxi: fix mac address for h6 devices 2022-04-08 11:28:31 +08:00
AmadeusGhost
726cbc3b62 sunxi: OrangePi One Plus: enable cpufreq support
Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
2022-04-08 11:25:28 +08:00
Christian Lamparter
70b774100f kernel: 5.10: silence bogus "Missing #address-cells in interrupt provider" warnings
Rosen reported strange dtc warnings that had their origin in
an upstream patch to 5.8-rc1. Upon further digging this
revealed an ongoing thread [0] discussing the topic:

> [...]I don't think we need a bunch of warning fix patches to add
> these everywhere. Also, the need for #address-cells pretty much makes
> no sense on any modern system. It is a relic from days when the bus
> (address) topology and interrupt topology were related.

and later on:
> So really, we only need to be checking for #address-cells in nodes
> with interrupt-map.

This patch backports just the patch which removed the warning message
(this is from the upstream dtc project [1] - but not the kernel).
the patch does not add the checking of the #address-cells in nodes
with interrupt-map.

[0] <https://lore.kernel.org/linux-devicetree/91e3405245c89f134676449cf3822285798d2ed2.1612189652.git.michal.simek@xilinx.com/>
[1] <https://git.kernel.org/pub/scm/utils/dtc/dtc.git/commit/?id=d8d1a9a77863a8c7031ae82a1d461aa78eb72a7b>
Link: <https://github.com/openwrt/openwrt/pull/4685>
Reported-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-04-07 11:36:50 +08:00
Christian Lamparter
0b68390514 apm821xx: WNDAP6X0: add missed uci-default for compat
This should have been included in the previous patch that
resized the kernel partition to fit bigger kernels.

Fixes: 7a6a349445 ("apm821xx: WNDAP620 + WNDAP660: reorganize partitions for 5.10")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-04-07 11:33:15 +08:00
Christian Lamparter
cd8c167643 apm821xx: implement new LED label naming scheme
This patch updates all current APM82181 devices over to that
"new LED naming scheme". This includes many updates to the
device-tree:
	- dropped the deprecated, but beloved "label" property.
	- rename all DT leds node names to led-#.
	- add function and color properties.
	- utilized panic-indicator property.
	- dropped led- aliases (see below).

migration scripts for all devices are included.

For more information. See:
<https://www.kernel.org/doc/html/latest/leds/leds-class.html>

For the future: It looks like the color+function properties
won over the dt-alias / label. This will need to be wired up
into openwrt eventually. For APM821xx the situation is that
all devices have a dedicated power and fault indicator.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-04-07 11:32:48 +08:00
Christian Lamparter
ab1aa8a02b ath79: lzma-loader: fix & re-enable per-board CONFIG_BOARD_DEV
Back in the AR71XX days, the lzma-loader code could be customized
based on the $BOARD variable. These would be passed as a
compile-time -DCONFIG_BOARD_$DEVICE_MODEL flag to the compiler.
Hence, the lzma-loader would be able to include device-specific
fixups.

Note: There's still a fixup for the TpLink TL-WR1043ND V1 found
in the lzma-loader's board.c code. But since the days of AR71XX
I couldn't find a forum post or bug reported. So, I left it
as is to not break anything by enabling it.

=> If you have a TL-WR1043ND V1 and you have problem with
the ethernet: let me know. Because otherwise, the fixup
might simply no longer needed with ath79 and it can be removed.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-04-07 11:29:47 +08:00
Christian Lamparter
7c109af148 apm821xx: MX60(W): re-enable + allow bigger future kernels
The MX60's kernel is limited to 0x3EFC00 by the values in
mkmerakifw.c. Since the initramfs method of loading the
kernel seems to be working, this patch does away with the
use of the mkmerakifw tool for the MX60(W).

But this will go along with a change in u-boot as well.
So before you upgrade, please attach the serial cable and
perform:

| setenv owrt510_boot run meraki_ubi owrt_bootargs\; run owrt_load1 owrt_bootkernel\; run owrt_load2 owrt_bootkernel
| setenv bootcmd run owrt510_boot
| saveenv

Note: You won't be able to use older OpenWrt releases without
switching the bootcmd back to owrt_boot!

Note2: We are no longer compatible with older OpenWrt MX60 installs.
the legacy BOARD_NAME and SUPPORTED_DEVICES can be dropped. This is
because upgrades from older images are not possible without uboot env
changes anymore. Also the bogus BLOCKSIZE value
(which was set to 63k back then, in order to get the kernel properly
aligned after the fdt + meraki header) can be set to the NANDs real
value. The FDT size (which was needed for alignment) can now be
slimmed down as well.

Co-developed-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Martin Kennedy <hurricos@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-04-07 11:29:18 +08:00
Christian Lamparter
9eba1c2bbf apm821xx: MBL: HDD regulators overhaul for MBL DUO
Takimata reported on the OpenWrt forum in thread [0], that his
MyBook Live Duo wasn't booting OpenWrt 21.02 after upgrading
from the previous OpenWrt 19.07.

The last logged entries on his console

|[    0.531599] sata1-regulator GPIO handle specifies active low - ignored
|[    0.538391] sata0-regulator GPIO handle specifies active low - ignored
|[    0.759791] ata2: SATA link down (SStatus 0 SControl 300)
|[    0.765251] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
|[    5.909555] ata1.00: qc timeout (cmd 0xec)
|[    5.913656] ata1.00: failed to IDENTIFY (I/O error, err_mask=0x4)
|[    6.231757] ata1: SATA link down (SStatus 0 SControl 300)

This extract clearly showed that the HDD on which OpenWrt is installed,
simply disappeared after the SATA power regulators had been initialized.

The reason why this worked with OpenWrt 19.07 was because the kernel
config symbol CONFIG_REGULATOR=y was not set in the target's config-4.14.

(This shows that the MBL Single does differ from the DUO in that
it does not have programmable power regulators for the HDDs.)

[0] <https://forum.openwrt.org/t/21-02-0-and-snapshot-fail-to-boot-on-my-book-live-duo/106585>

Reported-by: Takimata (forum)
Tested-by: Takimata (forum)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-04-07 11:29:04 +08:00
Roger Pueyo Centelles
18b9a20ec8 ath79: mikrotik: use 64 KiB SPI NOR erase sectors
This patch removes CONFIG_MTD_SPI_NOR_USE_4K_SECTORS from the default
symbols for the ath79/mikrotik target.

MikroTik devices hold some of their user-configurable settings in the
soft_config partition, which is typically sized 4 KiB, of the SPI NOR
flash memory. Previously, in the ar71xx target, it was possible to use
64 KiB erase sectors but also smaller 4 KiB ones when needed. This is
no longer the case in ath79 with newer kernels so, to be able to write
to these 4 KiB small partitions without erasing 60 KiB around, the
CONFIG_MTD_SPI_NOR_USE_4K_SECTORS symbol was added to the defaults.
However, this ended up making sysupgrade images which were built with
64 KiB size blocks not to keep settings (e.g., the files under
/etc/config/) over the flashing process.

Using 4 KiB erase sector size on the sysupgrade images (by setting
BLOCKSIZE = 4k) allows keeping settings over a flashing process, but
renders the process terribly slow, possibly causing a user to
mistakenly force a manual device reboot while the process is still on-
going. Instead, ditching the 4 KiB erase sectors for the default
64 KiB erase size provides normal SPI write speed and sysupgrade times,
at the expense of not being able to modify the soft_config partition
(which is rarely a required thing).

An OpenWrt patch for MTD_SPI_NOR_USE_4K_SECTORS_LIMIT may once have
allowed to use different per-partition erase sector sizes. Due to
changes on recent kernels it now only works on a per-device basis.
Also, partial eraseblock write can be performed in ath79 with kernels
5.4 and lower, by copying the blocks from the 64 KiB, erasing the whole
sector and restoring those blocks not meant to be modified. A kernel
bump had that patch broken for a long time, but got fixed in bf2870c.

Note: the settings in the soft_config partition can be reset to their
defaults by holding the reset button for 5 seconds (and less than 10
seconds) at device boot.

Fixes: FS#3492 (sysupgrade […] loses settings...)
Fixes: a66eee6336 (ath79: add mikrotik subtarget)

Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
2022-04-07 11:28:41 +08:00
AmadeusGhost
a53dd5c553 ipq806x: m520: enable pic support from chilau 2022-04-06 00:10:08 +08:00
Tianling Shen
c1b3ecc9fa
kernel: backport qrtr changes for 4.9/4.14
Required by package libqrtr-glib.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-04-03 20:08:26 +08:00
AmadeusGhost
398ea52770 [HOT FIX] Merge Mainline 2022-04-03 00:50:22 +08:00
AmadeusGhost
38bb0870ed sunxi: 5.10: add orangepi 3 support 2022-04-02 23:59:52 +08:00
AmadeusGhost
ce1978d646 sunxi: 5.4: reorder all patches 2022-04-02 23:58:23 +08:00
AmadeusGhost
dd5c4f4d6d sunxi: remove h6 pcie support
This will cause orangepi 3 to fail to boot on 5.10, so remove it.
2022-04-02 23:54:26 +08:00
Rafał Miłecki
2cca065af0 treewide: don't hardcode "sysupgrade.tgz" file name
1) Add BACKUP_FILE and use it when copying an archive to be restored
   after sysupgrade (on the next preinit).
2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
2022-04-02 00:29:37 +08:00
Andre Heider
cffa32b107 ipq40xx: add support for FRITZ!Box 7520
This model, also know as "1&1 HomeServer", shares the same features as 7530.

The vendor firmware has artificial software limitations: only 2 of the 4
LAN-Ports are GBit, and the USB-Host is only v2.0.

With OpenWrt, USB is already working at v3.0.

Signed-off-by: Andre Heider <a.heider@gmail.com>
(updated commit message to reflect current state)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-04-01 11:09:27 +08:00
Robert Marko
545aa5ce7b ipq40xx: mikrotik: fix LED script
Fix the missing ;; after the cAP ac case in /e/b/01_leds.

Fixes: 93d9119 ("ipq40xx: add MikroTik cAP ac support")
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (minor touch-up)
2022-04-01 11:09:09 +08:00
Pawel Dembicki
7ee6cf5317 ipq40xx: add support for ZTE MF286D
ZTE MF286D is a LTE router with four gigabit ethernet ports
and integrated QMI mPCIE modem.

Hardware specification:

  - CPU: IPQ4019
  - RAM: 256MB
  - Flash: NAND 128MB + NOR 2MB
  - WLAN1:  Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2
  - WLAN2:  Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2
  - LTE: mPCIe cat 12 card (Modem chipset MDM9250)
  - LAN: 4 Gigabit Ports
  - USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem)
  - Serial console: X8 connector 115200 8n1

Known issues:

  - Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs
    are driven by cpu.
  - Wifi LED is triggered by phy0tpt only
  - No VoIP support
  - LAN1/WAN port is configured as WAN
  - ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN
    and WLAN0/1

Opening the case:

1. Take of battery lid (no battery support for this model, battery cage
   is dummy).
2. Unscrew screw placed behind battery lid.
3. Take off back cover. It attached with multiple plastic clamps.
4. Unscrew four more screws hidden behind back case.
5. Remove front panel from blue chassis. There are more plastic
   clamps.
6. Unscrew two boards, which secures the PCB in the chassis.
7. Extract board from blue chassis.

Console connection (X8 connector):

1. Parameters: 115200 8N1
2. Pin description: (from closest pin to X8 descriptor to farthest)
    - VCC (3.3V)
    - TX
    - RX
    - GND

Install Instructions:

Serial + initramfs:
1. Place OpenWrt initramfs image for the device on a TFTP in
   the server's root. This example uses Server IP: 192.168.1.3
2. Connect serial console (115200,8n1) to X8 connector.
3. Connect TFTP server to RJ-45 port.
4. Stop in u-Boot and run u-Boot commands:
	setenv serverip 192.168.1.3
	setenv ipaddr 192.168.1.72
	set fdt_high 0x85000000
	tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb
	bootm $loadaddr
5. Please make backup of original partitions, if you think about revert
   to stock.
6. Login via ssh or serial and remove stock partitions:
	ubiattach -m 9
	ubirmvol /dev/ubi0 -N ubi_rootfs
	ubirmvol /dev/ubi0 -N ubi_rootfs_data
7. Install image via "sysupgrade -n".

Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
(cosmetic changes to the commit message)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-04-01 11:07:47 +08:00
Alar Aun
b2f9ec813a ipq40xx: add MikroTik cAP ac support
This adds support for the MikroTik RouterBOARD RBcAPGi-5acD2nD
(cAP ac), a  indoor dual band, dual-radio 802.11ac wireless AP, two
10/100/1000 Mbps Ethernet ports.

See https://mikrotik.com/product/cap_ac for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4018
 - RAM: 128 MB
 - Storage: 16 MB NOR
 - Wireless:
   · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae
   · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae
 - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 port,
   PoE in and passive PoE out

Unsupported:
 - PoE out

Installation:
Boot the initramfs image via TFTP and then flash the sysupgrade
image using "sysupgrade -n"

Signed-off-by: Alar Aun <alar.aun@gmail.com>
2022-04-01 11:03:26 +08:00
Sungbo Eo
7b1e4c49f6 ipq40xx: image: remove unused DTB_SIZE variable
It is not included in DEVICE_VARS anyways.

Signed-off-by: Sungbo Eo <mans0n@gorani.run>
2022-04-01 10:59:27 +08:00
Bjørn Mork
13dba15ccb ipq40xx: sysupgrade: drop disabled UBI to UBI logic
The commented out code is not required, as the comment
indicates.

The purpose of this code seems to be to avoid issues caused
by partially overwriting an existing UBI partition, where some
of the erase counters would be reset but not the unmodified
ones.  This problem has been solved in a more generic way by
the UBI EOF marker. This ensures that any old PEBs after the
marker are properly initialized.  It is therefore unnecessary
to erase the whole partition before flashing a new OpenWrt
factory image.

Signed-off-by: Bjørn Mork <bjorn@mork.no>
2022-03-29 16:29:52 +08:00
Enrico Mioso
a6c71e17dc ipq40xx: limit available radio channels for GL.iNet GL-B2200
The PCIe and built-in 5GHZ radios are meant to operate on different
frequency bands. The hardware enforces this via RF filters.
Add this information to allow software enforcing it as well.
Credits to Piotr Dymacz for the invaluable help.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
2022-03-29 16:28:59 +08:00
Enrico Mioso
7484b2d150 ipq40xx: fix reset button GPIO for GL.iNet GL-B2200
GL.iNet's U-Boot checks for GPIO 40, not 43.
Changing this allows the RESET button to work as expected.

Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
CC: Daniel Golle <daniel@makrotopia.org>
CC: Li Zhang <li.zhang@gl-inet.com>
2022-03-29 16:25:43 +08:00
TruongSinh Tran-Nguyen
d0a8040a3c ipq40xx: add support for GL.iNet GL-B2200
This patch adds supports for the GL-B2200 router.

Specifications:
  - SOC: Qualcomm IPQ4019 ARM Quad-Core
  - RAM: 512 MiB
  - Flash: 16 MiB NOR - SPI0
  - EMMC: 8GB EMMC
  - ETH: Qualcomm QCA8075
  - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
  - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
  - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
  - INPUT: Reset, WPS
  - LED: Power, Internet
  - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
  - UART2: On board with BLE module
  - SPI1: On board socket for Zigbee module

Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.

What's working:
- WiFi 2G, 5G
- WPA2/WPA3

Not tested:
- Bluetooth LE/Zigbee

Credits goes to the original authors of this patch.

V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade

Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
2022-03-29 16:24:49 +08:00
Christian Lamparter
fce3599a44 ipq40xx: unbreak EZVIZ CS-W3-WD1200G EUP on 5.10 2022-03-29 16:20:43 +08:00
Alexander Couzens
839f70cfd9 ipq40xx: add MikroTik LHGG-60ad outdoor 802.11ad (60GHz) dish
LHGG-60ad is IPQ4019 + wil6210 based.

Specification:

- Qualcomm IPQ4019 (717 MHz)
- 256 MB of RAM (DDR3L)
- 16 MB (SPI NOR) of flash
- 1x Gbit ethernet, 802.3af/at POE IN connected through AR8035.
- WLAN: wil6210 802.11ad PCI card
- No USB or SD card ports
- UART disabled
- 8x LEDs

Biggest news is the wil6210 PCI card.
Integration for its configuration and detection has already been taken
care of when adding support for TP-Link Talon AD7200.
However, signal quality is much lower than with stock firmware, so
probably additional board-specific data has to be provided to the
driver and is still missing at the moment.

Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
[Fix Ethernet Interface]
Signed-off-by: Nick Hainke <vincent@systemli.org>
2022-03-29 15:35:21 +08:00
Felix Matouschek
392629f4db ipq40xx: Add support for Teltonika RUTX10
This patch adds support for the Teltonika RUTX10.
This device is an industrial DIN-rail router with 4 ethernet ports,
2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs.

The RUTX series devices are very similiar so common parts of the DTS
are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev
board.

See https://teltonika-networks.com/product/rutx10 for more info.

Hardware:
  SoC:                 Qualcomm IPQ4018
  RAM:                 256MB DDR3
  SPI Flash 1:         XTX XT25F128B (16MB, NOR)
  SPI Flash 2:         XTX XT26G02AWS (256MB, NAND)
  Ethernet:            Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports
  WiFi 1:              Qualcomm QCA4019 IEEE 802.11b/g/n
  Wifi 2:              Qualcomm QCA4019 IEEE 802.11a/n/ac
  USB Hub:             Genesys Logic GL852GT
  Bluetooth:           Qualcomm CSR8510 (A10U)
  LED/GPIO controller: STM32F030 with custom firmware
  Buttons:             Reset button
  Leds:                Power (green, cannot be controlled)
                       WiFi 2.4G activity (green)
                       WiFi 5G activity (green)

MACs Details verified with the stock firmware:
   eth0:             Partition 0:CONFIG Offset: 0x0
   eth1:             = eth0 + 1
   radio0 (2.4 GHz): = eth0 + 2
   radio1 (5.0 GHz): = eth0 + 3
Label MAC address is from eth0.

The LED/GPIO controller needs a separate kernel driver to function.
The driver was extracted from the Teltonika GPL sources and can be
found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt

USB detection of the bluetooth interface is sometimes a bit flaky. When
not detected power cycle the device. When the bluetooth interface was
detected properly it can be used with bluez / bluetoothctl.

Flash instructions via stock web interface (sysupgrade based):
  1. Set PC to fixed ip address 192.168.1.100
  2. Push reset button and power on the device
  3. Open u-boot HTTP recovery at http://192.168.1.1
  4. Upload latest stock firmware and wait until the device is rebooted
  5. Open stock web interface at http://192.168.1.1
  6. Set some password so the web interface is happy
  7. Go to firmware upgrade settings
  8. Choose
     openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi
  9. Set 'Keep settings' to off
  10. Click update, when warned that it is not a signed image proceed

Return to stock firmware:
  1. Set PC to fixed ip address 192.168.1.100
  2. Push reset button and power on the device
  3. Open u-boot HTTP recovery at http://192.168.1.1
  4. Upload latest stock firmware and wait until the device is rebooted

Note: The DTS expects OpenWrt to be running from the second rootfs
partition. u-boot on these devices hot-patches the DTS so running from the
first rootfs partition should also be possible. If you want to be save follow
the instructions above. u-boot HTTP recovery restores the device so that when
flashing OpenWrt from stock firmware it is flashed to the second rootfs
partition and the DTS matches.

Signed-off-by: Felix Matouschek <felix@matouschek.org>
2022-03-29 15:33:41 +08:00
Robert Marko
2ecc6a2a29 ipq40xx: add support for MikroTik hAP ac3
This adds support for the MikroTik RouterBOARD RBD53iG-5HacD2HnD
(hAP ac³), a  indoor dual band, dual-radio 802.11ac
wireless AP with external omnidirectional antennae, USB port, five
10/100/1000 Mbps Ethernet ports and PoE passthrough.

See https://mikrotik.com/product/hap_ac3 for more info.

Specifications:
 - SoC: Qualcomm Atheros IPQ4019
 - RAM: 256 MB
 - Storage: 16 MB NOR + 128 MB NAND
 - Wireless:
   · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae
   · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi antennae
 - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port,
             passive PoE in, PoE passtrough on port 5
- 1x USB Type A port

Installation:
1. Boot the initramfs image via TFTP
2. Run "cat /proc/mtd" and look for "ubi" partition mtd device number, ex. "mtd1"
3. Use ubiformat to remove MikroTik specific UBI volumes
* Detach the UBI partition by running: "ubidetach -d 0"
* Format the partition by running: "ubiformat /dev/mtdN -y"
Replace mtdN with the correct mtd index from step 2.
3. Flash the sysupgrade image using "sysupgrade -n"

Signed-off-by: Robert Marko <robimarko@gmail.com>
Tested-by: Mark Birss <markbirss@gmail.com>
Tested-by: Michael Büchler <michael.buechler@posteo.net>
Tested-by: Alex Tomkins <tomkins@darkzone.net>
2022-03-29 15:28:17 +08:00
Christian Lamparter
86a606ec5e ipq40xx: purge clk_ignore_unused bootarg
these flags have been creeping in from the QSDK.
All needed clocks should be accounted for, and
if a device is broken due to this. It should be
looked into.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-29 15:24:40 +08:00
Christian Lamparter
e4db43f493 ipq40xx: update 105-ipq40xx-fix-sleep-clock.patch
Bjorn Anderson has suggestions which would help to upstream the patch.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-29 15:24:24 +08:00
Pavel Kubelun
3bdf5e7a2f ipq40xx: fix sleep clock
It seems like sleep_clk was copied from ipq806x.
Fix ipq40xx sleep_clk to the value QSDK defines.

Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [5.4+5.10]
2022-03-29 15:23:08 +08:00
Shiji Yang
517559af54 ramips: fix wifi mac address of HiWiFi series devices
For HiWiFi series devices, label_mac can be read from bdinfo partition,
and lan_mac, wlan2g_mac are same as the label_mac. Converting label_mac
to wlan5g_mac only needs to unset 6th bit. (It seems that all HiWiFi's
label_mac start with D4:EE)

For example:
label	D4:EE:07:32:84:88
lan	D4:EE:07:32:84:88
wan	D4:EE:07:32:84:89
wlan2g	D4:EE:07:32:84:88
wlan5g	D0:EE:07:32:84:88

Tested on HiWiFi HC5661.

Signed-off-by: Shiji Yang <yangshiji66@qq.com>
2022-03-28 16:17:03 +08:00
David Bauer
7a3b1745d9 ath79: fix link for long cables with OCEDO Raccoon
The OCEDO Raccoon had significant packet-loss with cables longer than 50
meter. Disabling EEE restores normal operation.

Also change the ethernet config to reduce loss on sub-1G links.

Signed-off-by: David Bauer <mail@david-bauer.net>
2022-03-28 16:15:05 +08:00
Aleksander Jan Bajkowski
c42f863639 kernel: move rtl8152 patches to generic
This commit moves the patches for the r8152.c driver to the generic
directory. Previously they were only available on the bcm27xx target.
With these patches the Realtek RTL8153C, RTL8153D, RTL8156A and RTL8156B
chips are supported on all targets by the kmod-usb-net-rtl8152 module.
The RTL8156A and RTL8156B are the 2.5Gb/s Ethernet adapters.

The patches have been tested on TP-Link UE300 (RTL8153A) and UNITEK
1313B (RTL8156B).

Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
2022-03-28 16:13:33 +08:00
Pascal Coudurier
cf08650493 kernel: backport two intel igc patches from 5.15
to allow proper initialization of device

- igc: Remove _I_PHY_ID checking
- igc: Remove phy->type checking

Signed-off-by: Pascal Coudurier <coudu@wanadoo.fr>
(refreshed)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-28 16:12:44 +08:00
Christian Lamparter
bea572b2cf apm821xx: fix crash/panic related to SATA/SSD choice
Ticerex on the OpenWrt Forum reported a gnarly crash when
he was using Samsung 840 and 850 EVOs with his MyBook Live:

| BUG: Kernel NULL pointer dereference at 0x00000000
| Faulting instruction address: 0xc03ed4b8
| Oops: Kernel access of bad area, sig: 11 [#1]
| BE PAGE_SIZE=4K PowerPC 44x Platform
| CPU: 0 PID: 362 Comm: scsi_eh_1 Not tainted 5.4.163 #0
| NIP:  c03ed4b8 LR: c03d27e8 CTR: c03ed36c
| REGS: cfa59950 TRAP: 0300   Not tainted  (5.4.163)
| MSR:  00021000 <CE,ME>  CR: 42000222  XER: 00000000
| DEAR: 00000000 ESR: 00000000
| GPR00: c03d27e8 cfa59a08 cfa55fe0 00000000 0fa46bc0 [...]
| [..]
| NIP [c03ed4b8] sata_dwc_qc_issue+0x14c/0x254
| LR [c03d27e8] ata_qc_issue+0x1c8/0x2dc
| Call Trace:
| [cfa59a08] [c003f4e0] __cancel_work_timer+0x124/0x194 (unreliable)
| [cfa59a78] [c03d27e8] ata_qc_issue+0x1c8/0x2dc
| [cfa59a98] [c03d2b3c] ata_exec_internal_sg+0x240/0x524
| [cfa59b08] [c03d2e98] ata_exec_internal+0x78/0xe0
| [cfa59b58] [c03d30fc] ata_read_log_page.part.38+0x1dc/0x204
| [cfa59bc8] [c03d324c] ata_identify_page_supported+0x68/0x130
| [...]

This turned out this is an issue with upstream changing
ATA_TAG_INTERNAL's value from 31 to 32 during 4.18 release.
Update "SATA_DWC_QCMD_MAX" to account for that.

Link: https://forum.openwrt.org/t/my-book-live-duo-reboot-loop/122464
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
2022-03-28 16:12:05 +08:00
Matthias Schiffer
275bb2b7de ath79: fix TPLINK_HWREV field for TL-WR1043ND v4
Required to allow sysupgrades from OpenWrt 19.07.

Closes #7071

Fixes: 98fbf2edc0 ("ath79: move TPLINK_HWID/_HWREV to parent for tplink-safeloader")
Tested-by: J. Burfeind <git@aiyionpri.me>
Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2022-03-28 16:10:54 +08:00
Tianling Shen
68c389e285
kernel: bump to 4.9.308, 4.14.273, 4.19.236
Refreshed all patches.

Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
2022-03-28 00:33:12 +08:00
Matthias Schiffer
d16776bc33 ath79: change Ubiquiti UniFi AP model name to include "AP"
While it hasn't always been clear whether the "AP" is part of the model
name on the Ubiquiti website, we include it for all other pre-AC
variants (AP Pro and the AP Outdoor+). Add it to the original UniFi AP
as well for consistency.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2022-03-25 10:39:55 +08:00
Matthias Schiffer
f3d410b279 ath79: fix label MAC address for Ubiquiti UniFi
The label has the MAC address of eth0, not the WLAN PHY address.

Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
2022-03-25 10:39:42 +08:00
Stijn Tintel
d25b1c602d kernel: enable SERIAL_8250_16550A_VARIANTS
Kernel 5.6 introduced a new config symbol SERIAL_8250_16550A_VARIANTS.
In kernel 5.8, this symbol was changed to default to on on !x86, as some
embedded devices still use 16650A variants. Let's play safe here and
enable this symbol in the generic config, to avoid others from running
into this problem and having to spend several hours trying to bisect
this problem. While we could disable the symbol in the x86 target
configs, a 20ms boot time reduction really isn't worth the time wasted
on bisecting this issue.

Matt discovered this problem while working on adding support for the
WatchGuard Firebox M200 to the qoriq target, where it caused some
characters to be missing on the console output.

Reported-by: Matt Fawcett <mattytap@icloud.com>
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Reviewed-by: Rui Salvaterra <rsalvaterra@gmail.com>
2022-03-25 10:38:51 +08:00
Stijn Tintel
f2ed18751e qoriq: enable I2C in target kernel config
The I2C controller used in QorIQ PPC devices requires the mpc-i2c
driver, which is enabled by the I2C_MPC kernel config symbol. Enable
this and its dependencies in the target kernel config, as is done for
the mpc85xx target.

This fixes missing hwmon, rtc and tpm devices on the M300.

Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
2022-03-25 10:37:24 +08:00