kdump was removed in 7acd257ae67b4ca94f8c23cb8bda0ee0709b9216
gdb can be used as an alternative.
Remove autoreconf. It's not needed as the configure files are already
generated.
Remove upstreamed patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
A SPI NOR flash should not be target-specific, so move it to generic in
case another platform needs to use it.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
FS#3574
Adding cgroup support enables adding rules on processes
to limit resources in terms of iptable policies
Signed-off-by: Supriya Mane <sm.supriya@globaledgesoft.com>
Without that, after merging support to master, the device fails to boot
due to LZMA decompression error:
3: System Boot system code via Flash.
## Booting image at bc080000 ...
raspi_read: from:80000 len:40
. Image Name: MIPS OpenWrt Linux-5.4.99
Created: 2021-02-25 23:35:00 UTC
Image Type: MIPS Linux Kernel Image (lzma compressed)
Data Size: 1786664 Bytes = 1.7 MB
Load Address: 80000000
Entry Point: 80000000
raspi_read: from:80040 len:1b4328
............................ Verifying Checksum ... OK
Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover
Use lzma-loader to fix it.
Fixes: 59d065c9f8 ("ramips: add support for ZTE MF283+")
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
HC5661 does not have USB port, remove usb power control pin.
HC5x61 do not have LAN LEDs, remove ethernet LED control pin.
Only HC5861 has PA in 2.4G channel.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Some users report that current snapshot producies non-bootable images.
Stock uboot can boot images if the kernel is smaller than 2MB.
Set maximum kernel size and disable image building for this board.
Ref: https://forum.openwrt.org/t/astoria-arv7519rw22-bootloops-after-upgrade/89843
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
Ubiquiti's own bootloader expects the configuration mode to be present
with a "@" instead of a "-" for the sperator character. Otherwise
booting of the image fails.
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes writing to the U-Boot environment by making the partition
writable and setting the correct flash sector size of 128K.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allow selecting either SATA or PCIE functionality using uImage.FIT
configurations and device-tree overlays.
By default, PCIE1 is selected (as it has been before this change).
To select SATA instead, you can do this now:
fw_setenv bootconf config-mt7622-bananapi-bpi-r64-sata
and reboot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Bananapi BPi-R64 got a SATA interface which cannot be used at the
same time as the second mPCIe slot. The decission is made by hogging
GPIO 90.
Embed two addtional DT overlay blobs into the image to allow bootloader
selection of either SATA or PCIE1 feature.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add new target feature 'dt-overlay' which makes DTC keep the symbol
names in the generated dtb.
Make sure additional DT overlay sources specified by the new device
variable DEVICE_DTS_OVERLAY get compiled together with the main DTS
(currently overlays got to be in the same folder). Let Build/fit pass
the generated DT overlay blobs to mkits.sh.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Allow adding multiple device tree overlay blobs to an image and
generate configurations for each of them.
This is useful on boards with modern U-Boot which allow e.g. user-
configurable peripherals ("shields") in that way.
Note that currently, each generated configuration adds exactly one
overlay on top of the base image, ie. adding multiple overlays at the
same time is not yet supported.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
DTR GPIO isn't actually needed and triggers boot warning.
TX pin was off by one (GPIO 19 instead of GPIO 18).
Reported-by: @tophirsch
Fixes: d1130ad265 ("ath79: add support for Teltonika RUT955")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop autogenerated kernel config options. These aren't needed to build and
can obscure options relevant to the subtarget.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
Update generic config to add missing options that prompt during builds. Run
"make kernel_oldconfig" to refresh malta target config.
Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
The rtl83xx-phy driver is necessary for proper configuration of the
PHYs if U-Boot hasn't done that.
1000Base-T SFPs often contains a Marvell 88E1111 and will not work
without this driver. Include it by default to support copper SFPs.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
This adds SFP sensors as a hwmon device, allowing readout of
temperatures, DOM and other sensor readings available from the
SFP.
Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
There is no need to define a static link or a phy for the sfp
ports. Using phy-mode and managed properties to describe the
link to the sfp phy.
We have to keep the now unconnected virtual "phys" because the
switch driver uses their "phy-is-integrated" property to figure
out which ports to enable as fibre ports.
Acked-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
From the validate docs in include/linux/phylink.h:
When state->interface is PHY_INTERFACE_MODE_NA, phylink expects the
MAC driver to return all supported link modes.
Tested-by: Birger Koblitz <mail@birger-koblitz.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Commit b5b0796a13 added an uint32_t to mtd.h without including stdint, which
results in a compilation error for those files not including stdint.h.
In file included from imagetag.c:36:
mtd.h:15:8: error: unknown type name 'uint32_t'
extern uint32_t opt_trxmagic;
^~~~~~~~
imagetag.c: In function 'trx_fixup':
imagetag.c:180:10: warning: unused variable 'res' [-Wunused-variable]
ssize_t res;
^~~
imagetag.c:177:14: warning: unused variable 'scan' [-Wunused-variable]
void *ptr, *scan;
^~~~
imagetag.c: In function 'trx_check':
imagetag.c:246:27: warning: initialization discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
struct bcm_tag *tag = (const struct bcm_tag *) buf;
^
make[3]: *** [<builtin>: imagetag.o] Error 1
Fixes: b5b0796a13 ("mtd: add option for TRX magic to fixtrx")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The ImageBuilder `make manifest` prints all installed packages. This
function can be used to create a list of package and corresponding
package versions before attempting image creation.
When called with `--strip-abi` OPKG can automatically strip attached
ABIVersions from package names. Make this function accessible for the
ImageBuilder by adding a `STRIP_ABI` variable.
Signed-off-by: Paul Spooren <mail@aparcar.org>
