Fix wrong magic number verification for FW files.
Correct handling of external RTL8218B firmware PHY name in firmware.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
The router profile installs many packages unnecessary for
the operation of a typical ethernet switch. Instead of creating
an empty switch profile upfront, use the basic profile until
a set of common packages crystallizes.
Signed-off-by: Andreas Oberritter <obi@saftware.de>
Fixes long delay on boot when booting from flash. The driver waits
for one minute for userspace to load firmware, before it becomes
available.
Signed-off-by: Andreas Oberritter <obi@saftware.de>
This adds basic support for reading the internal PHYs of the RTL839x SoCs
and full support for the 2 PHYs connected to the 1000Base-X SerDes of
the RTL8393 SoC.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
This adds correct interrupt routing settings for IRQs on the RTL839x SoCs.
It also speeds up irq handling based on work by biot for all SoCs.
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
The vDSO is used to accelerate some syscalls. It should work fine wherever it's
available, so enable it globally for all targets.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Commit "generic: ar8216: add mib_poll_interval switch attribute" has
added mib_poll_interval global config option and commit "generic:
ar8216: group MIB counters and use two basic ones only by default" has
added mib_type config option.
So this patch adds ucidef_set_ar8xxx_switch_mib helper function which
would allow configuration of the above mentioned new switch config
options.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The file /lib/functions/system.sh depends on find_mtd_index() and
find_mtd_part() located in /lib/function.sh, so let's source that
file.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
netifd does not handle network.@device[x].name properly if it
contains multiple ifaces separated by spaces. Due to this, board.d
lan_mac setup does not work if multiple ifaces are set to LAN by
ucidef_set_interface_lan.
To fix this, create a device node for each member iface when
running config_generate instead.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[always use new scheme, extend description, change commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
If set, label MAC address is available from one of two sources,
device tree or board.json. So far, the function get_mac_label
was meant for retrieving the address, while an option in uci
system config was specified only for case 2 (board.json).
The uci config option has several drawbacks:
- it is only used for a fraction of devices (those not in DT)
- label MAC address is a device property, while config implies
user interaction
- label_macaddr option will only be set if /etc/config/system
does not exist (i.e. only for new installations)
Thus, this patch changes the behavior of get_mac_label:
Instead of writing the value in board.json to uci system config
and reading from this location afterwards, get_mac_label now
extracts data from board.json directly. The uci config option
won't be used anymore.
In addition, two utility functions for extraction only from DT
or from board.json are introduced.
Since this is only changing the access to the label MAC address, it
won't interfere with the addresses stored in the code base so far.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For many devices, MAC addresses cannot be retrieved via the
device tree alias.
To still provide the label MAC address for those, this implements
a second mechanism that will put the address into uci config.
Note that this stores the actual MAC address, whereas in DTS
we reference the bearing device.
This is based on the work of Rosy Song <rosysong@rosinson.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
To refer to the MAC address on a device's label, one can
specify the alias label-mac-device in the DTS which should
point to the bearer of the corresponding MAC address.
With the function get_mac_label, the user can retrieve then
retrieve this address and use it as a value that uniquely
identifies his device.
This is severely helpful for several downstream functionalities,
e.g. define MAC addresses of custom netifs or change the SSID to
be easily recognizable.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The actual retrieval of the MAC address in mtd_get_mac_binary_ubi()
is the same as in get_mac_binary(). Thus, use the latter function
in the former to reduce duplicate code.
This will also allow to benefit from the enhanced path check there
and bring mtd_get_mac_binary_ubi() more in line with the similar
mtd_get_mac_binary().
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Logic was inverted when changing from string check to file check.
Fix it.
Fixes: 8592602d0a ("base-files: Really check path in get_mac_binary")
Reported-by: Matthias Schiffer <mschiffer@universe-factory.net>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Currently, path argument is only checked for being not empty.
This changes behavior to actually check whether path exists.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
vconfig has been disabled by default since 2015 [1] and there are
no remaining uses in entire OpenWrt trunk. However, we still set up
a specific name_type for it during boot.
While this setup is properly implemented to be only triggered when
vconfig is present, it still seems anachronistic and unnecessary
to set up a standard for a tool that is not used anymore.
Therefore, this removes the set_name_type initialization and leaves
it for those people actually using the tool to configure it as needed.
[1] 899a23227e ("busybox: improve applets & deprecate ifconfig, route")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Due to filesystem write caching the old configuration data could stay
out of flash for a long time during a first boot after the sysupgrade.
Power loss during this period could damage the overlay data and even
make device inaccessable via the network.
Fix this by syncing data to a flash as soon as the previous
configuration will be unpacked after the sysupgrade. Also sync the FS
state after the sysupgrade.tgz archive removing to prevent duplicative
extraction of a previous configuration.
Tested with AMD Geode based board.
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Kernel config option LEDS_TRIGGER_IDE_DISK was renamed in kernel 4.8 to
CONFIG_LEDS_TRIGGER_DISK in upstream commit eb25cb9956cc ("leds: convert
IDE trigger to common disk trigger").
Removing it as it should be added only on targets which has usage for
this trigger.
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
This changes the ide-disk LED trigger to the generic disk-activity as
ide-disk trigger was removed in upstream commit eb25cb9956cc ("leds:
convert IDE trigger to common disk trigger").
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[split into separate commit, commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
current preinit code in base-files doesn't config switch when there are
no port roles defined. But this kind of configuration exists on single
port devices where switch vlan is simply disabled.
configure reset and enable_vlan property when a switch node exist.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
This replaces deprecated backticks by more versatile $(...) syntax.
This does not touch lib/upgrade/nand.sh, as there replacement is
not trivial.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
uci-defaults are sourced and non-executable, so they do not require
a shebang.
While at it, apply consistent naming scheme.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
For devices such as BTHOMEHUBV5A with both reset and restart buttons,
its easily accessible restart button has been assigned to KEY_POWER
power script to poweroff preventing accidental (or malicious) factory
resets by KEY_RESTART reset script. However an easily accessible button
immediately powering off the device is also undesirable.
Fixes: FS#1965
Signed-off-by: Alan Swanson <reiver@improbability.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz> [long line wrap]
Restart is in default implemented so it calls stop and start. This is
pretty unsafe to call on umount service. This service should not do
anything on restart the same way as on start. Only use of this service
is on stop.
Signed-off-by: Karel Kočí <cynerd@email.cz>
This patch is in a series to allow additional STOP indexes after umount,
so that other block devices may stop cleanly.
boot is now STOP=90
umount is now STOP=90
Signed-off-by: Joseph Tingiris <joseph.tingiris@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
"coreutil-date" package from the packages feed replaces the Busybox date
applet by symlinking /usr/bin/gnu-date to /bin/date. This prevents the system
init script from setting kernel timezone because the GNU date utility does not
provide such functionality:
root@OpenWrt:~# date -k
date: invalid option -- 'k'
Try 'date --help' for more information.
A specific reference to the Busybox date applet prevents alternative date
utilities from breaking the system init script.
Signed-off-by: Val Kulkov <val.kulkov@gmail.com>
This adds a wrapper (uci_load_validate) for uci_validate_section() that
allows callers (through a callback function) to access the values set by
uci_validate_section(), without having to manually declare a
(potentially long) list of local variables.
The callback function receives two arguments when called, the config
section name and the return value of uci_validate_section().
If no callback function is given, then the wrapper exits with the value
returned by uci_validate_section().
This also updates several init scripts to use the new wrapper function.
Signed-off-by: Jeffery To <jeffery.to@gmail.com>
Part of the commit content is already in dropbear/files, procd/files,
ubox/files and busybox/files.
Commit ed5b9129d7 ("base-files: implement generic service_running")
has added EXTRA_HELP variable, thus overriding already available
EXTRA_HELP text available in other init scripts, resulting in the
missing help text from services like dropbear for example.
So fix this regression by appending EXTRA_HELP text provided by the
other init scripts into the one provided by the script itself.
Fixes: ed5b9129d7 ("base-files: implement generic service_running")
Signed-off-by: Peter Stadler <peter.stadler@student.uibk.ac.at>
[commit title/description facelift, fixes tag, fixed From:, pkg bump]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Adds a default status action for init.d scripts.
procd "service status" will return:
0) for loaded services (even if disabled by conf or dead)
3) for inactive services
4) when filtering a non-existing instance
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
[rebased, cleaned up]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Part of the commit content is already in system/procd/files.
Purpose of these changes is to introduce a hook for post service
shutdown in a similar fashion to the existing hook service_started. I
found it to be useful to specify a hook that is called once the service
has been stopped and not before the service is stopped like the
stop_service hook does.
The concrete use case I have for this is that I'm running a binary that
takes over the hardware watchdog timer. Said binary unfortunately can
not use ubus directly to tell procd to hand over the watchdog timer so
this has to be done in the service file for the binary in question. In
order to support a clean handover of the watchdog timer back to procd,
the service init script has to dispatch the ubus invocation once the
binary in question has been stopped.
Signed-off-by: Arthur Skowronek <ags@digineo.de>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
[added commit message, use the same form as other hooks]
Commit 124ab1dc0a and 5523ee3459 introduced the assignment of the
group "tty" to /dev/tty* devices in order to support unprivileged
user access to serial devices.
However, due to an improperly rebased commit this feature broke.
This patch restores the lost hunk in hotplug.json file to
re-introduce this feature and also renames the existing "tty" group
to "dialout" as this is the more typical name for such a group
on desktop systems.
Fixes: 5209cfa534 ("procd: fix hotplug.json syntax")
Signed-off-by: Michael Heimpold <mhei@heimpold.de>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Part of the commit content is already in system/procd/files.
For devices without a dedicated 'diag' LED, we use sometimes one of
other LEDs for indicating at least 'boot', 'failsafe' and 'upgrade'
stages. In some cases, at the same time these LEDs have defined default
triggers in DTS using 'linux,default-trigger' property. Current 'diag'
setup removes the trigger and turns off 'boot' LED after bootup.
This patch extends 'diag.sh' and 'leds.sh' scripts to make sure default
trigger defined in DTS is restored for 'diag' LED which isn't used for
indicating 'running' stage.
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The LED color was missing in 01_leds.
Fixes: 745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification
CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
DDR3 RAM: 256MB/512MB
Connectivity: 10/100/1000Mbps Ethernet
USB Host: Type-A x 1
MicroSD Slot x 1
MicroUSB: for power input only
Debug Serial Port: 4Pin, 2.54 mm pitch pin header
Power Supply: DC 5V/2A
PCB Dimension: 40 x 40 x 1.2mm
Installation:
Burn the image file to an SD Card with dd or any image burning tool
Boot ZeroPi from the SD Card
The following features are working and tested:
Ethernet port 10/100/1000M Ethernet
Remarks: SBC is mostly compatible and boots with FriendlyARM NanoPI M1 plus DTS also (zeropi has no working hdmi)
Signed-off-by: Arturas Moskvinas <arturas.moskvinas@gmail.com>
Tested on a A20 board:
$ cat /proc/asound/cards
0 [SPDIF ]: On-board_SPDIF - On-board SPDIF
On-board SPDIF
Size of the module for a 32bit kernel:
60708 linux-5.4.66/sound/soc/sunxi/sun4i-spdif.ko
Signed-off-by: Andre Heider <a.heider@gmail.com>
