Hardware:
- SoC: Mediatek MT7621 (MT7621AT)
- Flash: 32 MiB SPI-NOR (Macronix MX25L25635E)
- RAM: 128 MiB
- Ethernet: Built-in, 2 x 1GbE
- 3G/4G Modem: MEIG SLM828 (currently only supported with ModemManager)
- SLIC: Si32185 (unsupported)
- Power: 12V via barrel connector
- Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b
- Wifi 5GHz: Mediatek MT7613BE 802.11ac/n/a
- LEDs: 8x (7 controllable)
- Buttons: 2x (RESET, WPS)
Installing OpenWrt:
- sysupgrade image is compatible with vendor firmware.
Recovery:
- Connect to any of the Ethernet ports, configure local IP:
10.10.10.3/24 (or 192.168.10.19/24, depending on OEM)
- Provide firmware file named 'mt7621.img' on TFTP server.
- Hold down both, RESET and WPS, then power on the board.
- Watch network traffic using tcpdump or wireshark in realtime to
observe progress of device requesting firmware. Once download has
completed, release both buttons and wait until firmware comes up.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit bc335f2967)
Add configuration to access U-Boot environment on MeiG SLT866.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f8414f1a6f)
In addition to binary and ASCII-formatted MAC addresses, add support
for processing hexadecimal encoded MAC addresses from NVMEM.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 7db87d7c68)
Another Qualcomm-based USB-connected modem, offering endpoints
0 : rndis_host (link to voip subsystem listening on 169.254.5.100)
1 : rndis_host (?)
2 : option (?)
3 : option (at)
4 : option (at)
5 : option (?)
6 : GobiNet (qmi)
7 : ?
Add support for this modem in rndis_host, option and qmi_wwan driver
which allows the modem to be used with ModemManager.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit f32baf6a65)
Add support for COMFAST CF-EW72 V2
Hardware:
- SoC: Mediatek MT7621 (MT7621DAT or MT7621AT)
- Flash: 16 MiB NOR
- RAM: 128 MiB
- Ethernet: Built-in, 2 x 1GbE
- Power: only 802.3af PD on any port, injector supplied in the box
- PoE passthrough: No
- Wifi 2.4GHz: Mediatek MT7603BE 802.11b/g/b
- Wifi 5GHz: Mediatek MT7613BEN 802.11ac/n/a
- LEDs: 8x (only 1 is both visible and controllable, see below)
- Buttons: 1x (RESET)
Installing OpenWrt:
Flashing is done using Mediatek U-Boot System Recovery Mode
- make wired connection with 2 cables like this:
- - PC (LAN) <-> PoE Injector (LAN)
- - PoE Injector (POE) <-> CF-EW72 V2 (LAN). Leave unconnected to CF-EW72 V2 yet.
- configure 192.168.1.(2-254)/24 static ip address on your PC LAN
- press and keep pressed RESET button on device
- power the device by plugging PoE Injector (POE) <-> CF-EW72 V2 (LAN) cable
- wait for about 10 seconds until wifi led stops blinking and release RESET button
- navigate from your PC to http://192.168.1.1 and upload OpenWrt *-factory.bin firmware file
- proceed until router starts blinking with wifi led again (flashing) and stops (rebooting to OpenWrt)
MAC addresses as verified by OEM firmware:
vendor OpenWrt address
LAN lan\eth0 label
WAN wan label + 1
2g phy0 label + 2
5g phy1 label + 3
The label MAC address was found in 0xe000.
LEDs detailed:
The only both visible and controllable indicator is blue:wlan LED.
It is not bound by default to indicate activity of any wireless interfaces.
Place (WAN->ANT) | Num | GPIO | LED name (LuCI) | Note
-----------------|-----|-----------------------------------------------------------------------------------------
power | 1 | | | POWER LED. Not controlled with GPIO.
hidden_led_2 | 2 | 13 | blue:hidden_led_2 | This LED does not have proper hole in shell.
wan | 3 | | | WAN LED. Not controlled with GPIO.
hidden_led_4 | 4 | 16 | blue:hidden_led_4 | This LED does not have proper hole in shell.
lan | 5 | | | LAN LED. Not controlled with GPIO.
noconn_led_6 | 6 | | | Not controlled with GPIO, possibly not connected
wlan | 7 | 15 | blue:wlan | WLAN LED. Wireless indicator.
noconn_led_8 | 8 | | | Not controlled with GPIO, possibly not connected
mt76-phy0 and mt76-phy1 leds also exist in OpenWrt, but do not exist on board.
Signed-off-by: Alexey D. Filimonov <alexey@filimonic.net>
(cherry picked from commit ff95f859eb)
Add support for ComFast CF-E390AX. It is a 802.11 wifi6 cieling AP, based on MediaTek MT7261AT.
Specifications:
SoC: MediaTek MT7621AT
RAM: 128 MiB
Flash: 16 MiB NOR (Macronix mx25l12805d)
Wireless: MT7915E (2.4G) 802.11ax/b/g/n MT7915E (5G) 802.11ac/ax/n
Ethernet: 2 x 1Gbs
Button: 1 x "Reset" button
LED: 1x Blue LED + 1x Red LED + 1x green LED
Power: PoE
Manufacturer Page:
http://en.comfast.com.cn/index.php?m=content&c=index&a=show&catid=84&id=75
Flash Layout:
0x000000000000-0x000000030000 : "bootloader"
0x000000030000-0x000000040000 : "config"
0x000000050000-0x000000060000 : "factory"
0x000000090000-0x000001000000 : "firmware"
First install:
1. Set device into http firmware fail safe upload mode by pressing the reset button for 10 seconds while powering
it on. Once the LED stops flashing, safe mode will be running.
2. Set PC IP address to 192.168.1.2
3. Browse to 192.168.1.1 and upload the factory image using the web interface.
Signed-off-by: Usama Nassir <usama.nassir@gmail.com>
(cherry picked from commit f24c9b9d86)
With the case of asking an invalid version that is too big, getver.sh
might return an invalid output in the form of HEAD~-2260475641.
This is caused by BASE_REV - GET_REV using a negative number.
Prevent this by checking if BASE_REV - GET_REV actually return 0 or a
positive number and set REV variable accordingly. With the following
change, invalid revision number will result in unknown printed instead
of the invalid HEAD~-NUMBERS output.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 9e49e0a6c4)
eee02ccca8c8 device: add support to configure eee
bb28f6a291d9 wireless: fix sign comparison warning
35facc8306f5 wireless: fix premature removal of hotplug devices due to down state
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit d45d72a6da)
841b05fbb91e system-linux: fix compilation error if IFLA_DSA_MASTER is not supported
5c9ecc1ff74f system-linux: make system_if_get_master_ifindex static
2dc7f450f3a2 system-linux: add option to configure DSA conduit device
838f815db5ef system-linux: add support for configurable GRO option
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 1714087442)
0352a33 uloop: support new interval and signal APIs
1468cc4 syntax: don't treat `as` and `from` as reserved keywords
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
(cherry picked from commit 551963662b)
Refresh patches for hostapd using make package/hostapd/refresh.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 05e516b12d)
Currently for 802.1s only, for wifi 2.4GHz in g/n mode, 40MHz is never
permitted.
This is probably due to the complexity of setting periodic check for the
intolerant bit. When noscan option is set, we ignore the presence of the
intoleran bit in near AP, so we can enable 40MHz and ignore any complex
logic for checking.
Fixes: #13112
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 6c9ac57d58)
Also channel 7 for 2.4GHz can be set to HT40PLUS. Permit this and add it
to the list of the channels.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit b1c7b1bd67)
noscan option for mesh was broken and actually never applied.
This is caused by a typo where ssid->noscan value is check instead of
conf->noscan resulting in the logic swapped and broken.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 1b5ea2e199)
noscan option was changed to hostapd_noscan but the entry in
wpa_supplicant was never updated resulting in the noscan option actually
never set.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
(cherry picked from commit 1070fbce6e)
- Fixed PCIe reset
- Fixed reset button, WLAN LEDs
- Fixed sysupgrade feature
- Fixed NVMEM bindings
This requires install new custom U-Boot, which can be downloaded at:
https://firmware.download.immortalwrt.eu.org/uboot/ramips/mt7621-zte_e8820s-u-boot.bin
Or build it manually:
git clone https://github.com/DragonBluep/uboot-mt7621 && cd uboot-mt7621
./customize.sh NAND '2176k(Bootloader),1280k(config),1280k(factory),-(firmware)' \
'0x4a0000' '18' '16' '880' '1200' 'DDR3-512MiB' 'false' '115200'
Flash instructions for existing users:
1. Run the following commands on device:
opkg install kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
mtd write mt7621-zte_e8820s-u-boot.bin u-boot
2. Cut off the power and re-engage, enter 192.168.1.1 to upload initramfs.bin.
3. After ImmortalWrt has booted, perform sysupgrade.
Flash instructions for new users:
1. Rename the U-Boot file to `ZTE_img.bin`
2. Set static IP on your PC:
IP 192.168.1.2/24, GW 192.168.1.254
3. Serve the U-Boot file using TFTP server.
4. Cut off the power, keep pressing `reset` button then engage the power.
5. Wait for U-Boot download to complete, enter 192.168.1.1 to upload initramfs.bin.
6. After ImmortalWrt has booted, perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 85e0f369a0)
Store the private key with read and write permission for the user only
and not with read permissions for everyone. This converts the
write_file() function from fopen() to open() because open allows to
specify the permission mask of the newly created file. It also adds and
fixes some existing error handling.
OpenSSL does this in the same way already.
With this change it looks like this:
root@OpenWrt:/# ls -al /etc/uhttpd.*
-rw-r--r-- 1 root root 749 Nov 6 23:14 /etc/uhttpd.crt
-rw------- 1 root root 121 Nov 6 23:14 /etc/uhttpd.key
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 6aad5ab099)
Store the private key with read and write permission for the user only
and not with read permissions for everyone. This converts the
write_file() function from fopen() to open() because open allows to
specify the permission mask of the newly created file. It also adds and
fixes some existing error handling.
OpenSSL does this in the same way already.
With this change it looks like this:
root@OpenWrt:/# ls -al /etc/uhttpd.crt /etc/uhttpd.key
-rw-r--r-- 1 root root 519 Nov 6 22:58 /etc/uhttpd.crt
-rw------- 1 root root 121 Nov 6 22:58 /etc/uhttpd.key
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 929c9a58c9)
Apply them directly using nl80211 after setting up the interface.
Use the same method in wdev.uc as well
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 531314260d)
383753dd65ae device/bridge: support passing extra vlans in the device_set_state call
b6e75eafc1af device: send notifications for device events via ubus
cab415c7aefd bridge: add auth-required bridge members with auth_status=0 if vlan is enabled
827a02f0343c bridge: add support for configuring vlans for auth=1,auth_status=false
40ed7363caf2 device: fix build error on 32 bit systems
516ab774cc16 system-linux: fix race condition on bringing up wireless devices
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 41d7439af5)
Hardware specification:
SoC: MediaTek MT7981B 2x A53
Flash: 64GB eMMC or 128 MB SPI-NAND
RAM: 512MB
Ethernet: 4x 10/100/1000 Mbps
Switch: MediaTek MT7531AE
WiFi: MediaTek MT7976C
Button: Reset, Mesh
Power: DC 12V 1A
- UART: 3.3v, 115200n8
--------------------------
| Layout |
| ----------------- |
| 4 | GND TX VCC RX | <= |
| ----------------- |
--------------------------
Gain SSH access:
1. Login into web interface, and download the configuration.
2. Enter fakeroot, decompress the configuration:
tar -zxf cfg_export_config_file.conf
3. Edit 'etc/config/dropbear', set 'enable' to '1'.
4. Edit 'etc/shadow', update (remove) root password:
'root::19523:0:99999:7:::'
5. Repack 'etc' directory:
tar -zcf cfg_export_config_file.conf etc/
* If you find an error about 'etc/wireless/mediatek/DBDC_card0.dat',
just ignore it.
6. Upload new configuration via web interface, now you can SSH to RAX3000M.
Check stroage type:
Check the label on the back of the device:
"CH EC CMIIT ID: xxxx" is eMMC version
"CH CMIIT ID: xxxx" is NAND version
eMMC Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'factory' part.
('data' partition can be ignored, it's useless.)
2. Write new GPT table:
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-gpt.bin of=/dev/mmcblk0 bs=512 seek=0 count=34 conv=fsync
3. Erase and write new BL2:
echo 0 > /sys/block/mmcblk0boot0/force_ro
dd if=/dev/zero of=/dev/mmcblk0boot0 bs=512 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-preloader.bin of=/dev/mmcblk0boot0 bs=512 conv=fsync
4. Erase and write new FIP:
dd if=/dev/zero of=/dev/mmcblk0 bs=512 seek=13312 count=8192 conv=fsync
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-emmc-bl31-uboot.fip of=/dev/mmcblk0 bs=512 seek=13312 conv=fsync
5. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
6. Serve OpenWrt initramfs image using TFTP server.
7. Cut off the power and re-engage, wait for TFTP recovery to complete.
8. After OpenWrt has booted, perform sysupgrade.
9. Additionally, if you want to have eMMC recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
dd if=openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb of=/dev/mmcblk0p4 bs=512 conv=fsync
NAND Flash instructions:
1. SSH to RAX3000M, and backup everything, especially 'Factory' part.
2. Erase and write new BL2:
mtd erase BL2
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-preloader.bin BL2
3. Erase and write new FIP:
mtd erase FIP
mtd write openwrt-mediatek-filogic-cmcc_rax3000m-nand-bl31-uboot.fip FIP
4. Set static IP on your PC:
IP 192.168.1.254, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt has booted, erase UBI volumes:
ubidetach -p /dev/mtd0
ubiformat -y /dev/mtd0
ubiattach -p /dev/mtd0
8. Create new ubootenv volumes:
ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB
ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
9. Additionally, if you want to have NAND recovery boot feature:
(Don't worry! You will always have TFTP recovery boot feature.)
ubimkvol /dev/ubi0 -n 2 -N recovery -s 20MiB
ubiupdatevol /dev/ubi0_2 openwrt-mediatek-filogic-cmcc_rax3000m-initramfs-recovery.itb
10. Perform sysupgrade.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit 423186d7d8)
[rebased to 23.05]
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The OEM U-Boot uses dual boot and signature verification which does not
support by OpenWrt. So add a custom U-Boot build for OpenWrt.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
(cherry picked from commit fddd735dd5)
Activate the secp521r1 ecliptic curve by default. This curve is allowed
by the CA/Browser forum, see
https://cabforum.org/wp-content/uploads/CA-Browser-Forum-BR-v2.0.1-redlined.pdf#page=110
This increases the size of libmbedtls12_2.28.5-1_aarch64_generic.ipk by
about 400 bytes:
Without:
252,696 libmbedtls12_2.28.5-1_aarch64_generic.ipk
With:
253,088 libmbedtls12_2.28.5-2_aarch64_generic.ipk
Fixes: #13774
Acked-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
(cherry picked from commit 3c17cdbc36)
Changes introduced in commit d604a07225 ("build: add CycloneDX SBOM
JSON support") broke ImageBuilder:
Cannot open '/openwrt-imagebuilder-ath79-generic.Linux-x86_64/tmp/.packageinfo': No such file or directory
So lets fix it by wrapping the BOM generation behind condition of IB
feature check.
Fixes: #13881
Fixes: d604a07225 ("build: add CycloneDX SBOM JSON support")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit c4259a6586)
Some packages (like wavemon >= 0.9.4) depend on libnl-cli. Add support
for this part of the lib. libnl-cli itself depends on libnl-genl and
libnl-nf. On MIPS, this component adds 81kB.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
(punctuation correction and reorganisation of commit message)
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 4bdd1c1a13)
Some packages (like wavemon >= 0.9.4) depend on libnl-cli. Add support
for this part of the lib. libnl-cli itself depends on libnl-genl and
libnl-nf. On MIPS, this component adds 81kB.
Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
(punctuation correction and reorganisation of commit message)
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 4bdd1c1a13)
Changes:
6b2533c0 libnl-3.8.0 release
1558bd62 build: replace old "NOTE" in configure output and add summary
f66383a4 build: avoid aclocal warning about missing "m4" directory
e4402a4c build: run `autoupdate` for AM_PROG_LIBTOOL
5761b6af build: add "-Wno-portability" to AC_INIT_AUTOMAKE()
661f10a1 license: fix/adjust license for "src/nl-cls-add.c"
c8fcb412 license: fix/adjust license for "src/nl-addr-{add,delete,list}.c"
e3e6fd6d tests: use thread-safe localtime_r() instead of localtime()
f520471c lib/xfrm: use thread-safe gmtime_r() instead of gmtime()
be5add72 tests: avoid srandom()/random() in favor of _nltst_rand_u32()
40578a62 lib: use getprotobyname_r(), getprotobynumber_r() if available
8ee8b05f lib: fix error handling in nl_str2ip_proto()
09f03f29 tests: check nl_str2ip_proto()
74bffbf6 route: fix documentation comment for nl_nh_group_info
59f8db0d clang-format: add "-l" alias for option in "tools/clang-format.sh"
935cc90a clang-format: ignore reformatting commit in ".git-blame-ignore-revs"
53da4712 clang-format: reformat files with new format
65c43bfe clang-format: update ".clang-format" from linux kernel
4c39a2ce include: use <linux/$file> instead of <linux-private/linux/$file>
a1e9fb3d include/linux: add all linux headers that we use
d37ffe15 include/linux: update all linux headers
1af767a8 include: add missing "extern "C"" specifier to public headers
e0a5d12b all: drop "extern "C"" from internal code
d9a1e0ce build: add "check-local-build-headers" test target to build public headers
02b87012 build: add a "check-local" build target
f9413915 include: fix headers "include/netlink/route/{netconf.h,route/qdisc/red.h}" to be self-contained
680df173 idiag: "fix" license for "idiag-socket-details" tool
2f210d9a github: test build on alpine:latest for musl
dcc4c0a5 Revert "gitignore: ignore patch files"
39106309 github: add test for linking with mold and fail on unknown versions
f475c3b2 route/nh: drop not implemented "nh" API from headers
4c681e77 build: fix exporting symbol rtnl_link_info_ops_get
260c9575 include: don't explicitly include headers from "nl-default.h"
98c1e696 tests: cleanup include of netlink headers
42bec462 build: cleanup default include list in Makefile.am
4c1a119a include: include private linux headers with explicit path
ca063725 python: add make target for python build
25c90193 python: drop unused "python/netlink/fixes.h"
3f3da7fd gitignore: ignore python build artifacts
61ef5609 gitignore: ignore generated doc files
298c5dc6 include: drop "netlink-private/netlink.h" and move declarations
862eed54 all: cleanup includes and use "nm-default.h"
2b3cd741 include: add "nl-default.h" header
8952ce6f build: move "lib/defs.h" to "include/config.h"
1010776d include: split and drop "netlink-private/types.h"
d1d57846 include: rename "nl-shared-core" to "nl-priv-dynamic-core"
fc91c4f8 include: rename "nl-hidden-route" to "nl-priv-dynamic-route"
9bb6f770 include: rename "nl-intern-route" to "nl-priv-static-route"
b5195db9 genl: rename private header "nl-priv-genl.h" to "nl-genl.h"
0eacf658 include: make "netlink/route/link/{inet,inet6}.h" self-contained
ad014ad1 route/tc: avoid unalinged access in rtnl_tc_msg_parse()
05bd6366 add support for TC action statistics
776fc5a6 lib: move "include/netlink-private/object-api" to include/nl-shared-core
fad34560 lib: move "include/netlink-private/cache-api" to include/nl-shared-core
ed2be537 route: move "include/netlink-private/route/link/sriov.h" to lib/route/link-sriov.h
97f61eda lib: move "include/netlink-private/socket.h" to lib/nl-core.h
96e1cc5b route: move "include/netlink-private/route/nexthop-encap.h" to lib/route
391e03d3 route: merge "include/netlink-private/tc.h" to lib/route/tc-api.h
7fc4f5b3 route: move rtnl_tc_build_rate_table() to "tc-api.h"
cf41e14d route: move "include/netlink-private/route/tc-api.h" to lib/route
db810cfb route: move hidden symbols from "include/netlink-private/route/tc-api.h"
ff08e618 build: don't add lib/route to include directory for all libs
eb8da16d include: move "include/netlink-private/route/link/api.h" to lib/route
8b2074aa include: move "include/netlink-private/route/utils.h" to nl-intern-route
fd470c06 include: move "include/netlink-private/route/mpls.h" to "lib/mpls.h"
78056ad2 genl: add comment about wrongly exported symbol genl_resolve_id()
befc4ab4 include: move "include/netlink-private/genl.h" to "lib/genl/nl-priv-genl.h"
f6c26127 nl-aux: add "include/nl-aux-{core,route}" headers
2da8481b base: move "netlink-private/utils.h" to "base/nl-base-utils.h"
d3e9b513 include/utils: move nl-auto base defines to "utils.h"
543b9f8f clang-format: reformat "include/netlink-private/nl-auto.h"
aa565460 route: cleanup ATTR_DIFF() macros
beba5a18 cli: add nl-nh-list utility
780d06ae route: add nh type
1b6433d9 neigh: add support of NHID attribute
e0140c5f include: import kernel headers "linux/{neighbour,nexthop,rtnetlink}.h"
eef06744 utils: add static-assert for signedness of arguments of _NL_CMP_DIRECT() macro
679c4c51 cli: use <netlink-private/utils.h> in cli and _nl_{init,exit}
a9c5de52 lib: use _nl_{init,exit} instead of __{init,exit}
102f9bd2 include/private: add _nl_init/_nl_exit macros
6782678e include/private: drop unused __deprecated macro
a0535a58 all: use "_nl_packed" macro instead of "__attribute__((packed))"
8c9f98cf all: rework ATTR_DIFF() macros to not generate attribute names
ca34ad52 lib: handle negative and zero size in nla_memcpy()
859b89dc include: drop now unused min()/max()/min_t()/max_t() macros
2e0ae977 all: use _NL_{MIN,MAX}() macros
57c451fa utils: add various helpers to "include/netlink-private/utils.h"
a9a9dcea style: format "include/netlink-private/utils.h" with clang-format
590e8a61 tools: improve failure message with "tools/clang-format.sh -n"
06dc5ae0 github: fix format checking with clang-format
7738f239 route/trivial: sort entries in "libnl-route-3.sym" asciibetically
fc805c56 route/bond: Add support for link_info for bond
6af26981 lib: accept NULL argument in nla_nest_cancel() for robustness
e9662091 macsec: Drop offload capability validation check
35a68109 github: update flake8 linter to not explicitly select checks
9a266405 python: add ".flake8" file for configuring "flake8"
e6b934a5 python: fix flake8 warnings E712
2cea738b python: fix flake8 warnings E711
d561096c python: fix flake8 warnings E302
29b06d0f python: fix flake8 warnings E741
4dc1f498 python: fix flake8 warnings F841
f4875c69 python: fix flake8 warnings W605
9a3d91df python: fix flake8 warnings F401
6baf2339 clang-format: add "tools/clang-format-container.sh" script
ee2876e3 github: add test for checking clang-format style
45c7aae3 clang-format: add "tools/clang-format.sh" script
02e0fd3f github: check python-black code formatting in github actions
2dd53895 build: add ".git-blame-ignore-revs" file for "blame.ignoreRevsFile" git config
3c753e3c python: reformat all Python files with python-black
298ee58e python add "pyproject.toml" for configuring black
a0e4b7f9 github: skip Python flake8 test with clang build
c4240c0b github: run "Build Release" test also with clang
143cee1d bridge: fix bridge info parsing
96bbe55c test-cache-mngr: Flush output after object dumps
cf5dcbcd test-cache-mngr: Add option to print timestamps
bd570952 test-cache-mngr: Add an option to iterate over all supported address families
bf80da90 test-cache-mngr: Add dump interval options
80febeea test-cache-mngr: Add an option to control which oo_dump function is used
6519a917 route/link: prevent segfault in af_request_type()
a68260f8 github: fix installing python dependencies via pip
39c04bc7 build: drop redundant "autogen.sh" call from "tools/build_release.sh"
d411b88d build: change proper working directory in "doc/autogen.sh"
2fa73ce0 build: ensure "autogen.sh" scripts fail on error
fc786296 gitignore: ignore "*~" files
4c4e614b docs: rtnl_link_put() 'releases' instead of 'returns'
336b15dc include/linux: update copy of kernel header "linux/ipv6.h"
e2cacc26 route/link: improve handling of IFLA_INET6_CONF
ec8c493c route/link: remove rtnl_link_inet6_set_conf() API
e790f8ad route/link: various fixes for rtnl_link_inet6_get_conf() API
d83c6d54 route/link: add accessor API for IPv6 DEVCONF
9167504d bridge: drop unnecessary goto in bridge_info_parse()
984d6e93 bridge: don't normalize the u8 argument in rtnl_link_bridge_set_vlan_filtering() to boolean
3662a5da bridge: expose rtnl_link_bridge_get_vlan_protocol() in host byte order
5a1ef219 bridge: fix parsing vlan-protocol in bridge_info_parse()
ad1c2927 bridge: minor cleanups in "bridge_info.c"
1c74725a bridge: use SPDX license identifiers in bridge_info files
26ca549d bridge: reformat bridge_info file with clang-format
08dc5d9c bridge: extend libnl with options needed for VLAN aware forwarding
7391a38e bridge: Add support for link_info of a bridge
1f1e8385 route/vlan: drop unnecessary "else" in vlan_put_attrs()
2bc30e57 route/vlan: fix error handling in 'lib/route/link/vlan.c'
8273d6ce build: add comments to linker version scripts about the version tags
6ac7a812 doc: fix typo
07d274ab doc: fix typo
0461a425 attr: reject zero length addresses
8d40d9eb route: construct all-zero addresses for default route destination
25d42a4f addr: allow constructing all-zero addresses
0c0aee82 addr: create an all-zero addresses when parsing "any" or "default"
Signed-off-by: Nick Hainke <vincent@systemli.org>
(cherry picked from commit 4e5d45f1e6)
The router use mt7986_eeprom_mt7976_dual.bin
Fixes: d522ccecb2 ("filogic: add support for ASUS TUF AX6000")
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(cherry picked from commit 0c3f4bd85e)
Hardware
========
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R
ETH: MediaTek MT7530 Switch (LAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
UART: 3V3 115200 8N1 (Do not connect VCC)
USB 3.1
Installation
============
Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin.
Connect to the serial console, interrupt the auto boot process by
pressing '4' when prompted or press '1' and set client IP, server
IP and name of the image.
yOU don't need to open the case or even soldering anything.
use three goldpin wires, remove their plastic cover and connect
them to the console pinout via the case holes.
You can see three holes
From Bottom: RX, TX, Ground - partially covered
Download & Boot the OpenWrt initramfs image.
In case of option '4'
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 TUF-AX6000.bin
$ bootm 0x46000000
In case of option '1'
1: Load System code to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (TUF-AX6000.trx) ==:
Wait for OpenWrt to boot. Transfer the sysupgrade
image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
================
2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected
The cover yellow light is not supported. (only blue one)
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(cherry picked from commit d522ccecb2)
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.
[1] Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
(cherry picked from commit 36746893ac)
