The router use mt7986_eeprom_mt7976_dual.bin
Fixes: d522ccecb2 ("filogic: add support for ASUS TUF AX6000")
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(cherry picked from commit 0c3f4bd85e)
Hardware
========
SOC: MediaTek MT7986
RAM: 512MB DDR3
FLASH: 256MB SPI-NAND
WIFI: Mediatek MT7986 DBDC 802.11ax 2.4/5 GHz 4T4R
ETH: MediaTek MT7530 Switch (LAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (WAN)
MaxLinear GPY211C 2.5 N-Base-T PHY (LAN)
UART: 3V3 115200 8N1 (Do not connect VCC)
USB 3.1
Installation
============
Download the OpenWrt initramfs image. Copy the image to a TFTP server
reachable at 192.168.1.70/24. Rename the image to TUF-AX6000.bin.
Connect to the serial console, interrupt the auto boot process by
pressing '4' when prompted or press '1' and set client IP, server
IP and name of the image.
yOU don't need to open the case or even soldering anything.
use three goldpin wires, remove their plastic cover and connect
them to the console pinout via the case holes.
You can see three holes
From Bottom: RX, TX, Ground - partially covered
Download & Boot the OpenWrt initramfs image.
In case of option '4'
$ setenv ipaddr 192.168.1.1
$ setenv serverip 192.168.1.70
$ tftpboot 0x46000000 TUF-AX6000.bin
$ bootm 0x46000000
In case of option '1'
1: Load System code to SDRAM via TFTP.
Please Input new ones /or Ctrl-C to discard
Input device IP (192.168.1.1) ==:
Input server IP (192.168.1.70) ==:
Input Linux Kernel filename (TUF-AX6000.trx) ==:
Wait for OpenWrt to boot. Transfer the sysupgrade
image to the device using scp and install using sysupgrade.
$ sysupgrade -n <path-to-sysupgrade.bin>
Missing features
================
2.5Gb LAN port LED is ON during boot or when the LAN cable is disconnected
The cover yellow light is not supported. (only blue one)
Signed-off-by: Patryk Kowalczyk <patryk@kowalczyk.ws>
(cherry picked from commit d522ccecb2)
Fix the issue of dts buswidth cannot be applied properly with spi driver.
Fix the name of buswidth to bus-width in dts in order to fit the format
in linux spi kernel[1] so that spi-tx-bus-width & spi-rx-bus-width can be
parsed properly.
[1] Documentation/devicetree/bindings/spi/spi-controller.yaml
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
(cherry picked from commit 36746893ac)
The MAC-address of gmac0 matches the one printed on the bottom label.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit ae500e62e2)
d8118f6 config: make sure timer is not on the timeouts list before freeing
4bbc6e7 add hostsfile output in addition to statefile
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
(cherry picked from commit 0221b86032)
With patch 101-03-spi-mtk_spim-get-spi-clk-rate-only-once.patch
a new system to calculate the SPI clocks has been added.
Unfortunately, the do_div macro overrides the global
priv->pll_clk_rate field. This will cause to have a reduced
clock rate on each subsequent SPI call.
Signed-off-by: Valerio 'ftp21' Mancini <ftp21@ftp21.eu>
Signed-off-by: Nicolò Veronese <nicveronese@gmail.com>
(cherry picked from commit 8849ccb995)
The output of command_all when inside a nix-shell looks like the below
where /usr does not match:
➜ scripts/command_all.sh pkg-config
/nix/store/ifr6srqgpvygd5vp14748d109ri31isv-pkg-config-wrapper-0.29.2/bin/pkg-config
Signed-off-by: Sandro Jäckel <sandro.jaeckel@gmail.com>
(cherry picked from commit 86ca7199df)
Implement a GitHub Actions workflow for automated project releases.
The workflow triggers on Git tags, ensuring that a GitHub release is
created whenever a new tag is pushed.
That new release is going to be created in draft and pre-release mode
and needs to be manually promoted to the proper release, once its
decided, that its good enough and prepared.
This is a start of a streamlined and consistent release process for
GitHub, reducing manual intervention.
Acked-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 280d9dd758)
Upgrading wpa_supplicant from 2.9 to 2.10 breaks broadcom-wl/ath11k
based adapters. The reason for it is hostapd tries to install additional
IEs for scanning while the driver does not support this.
The kernel indicates the maximum number of bytes for additional scan IEs
using the NL80211_ATTR_MAX_SCAN_IE_LEN attribute. Save this value and
only add additional scan IEs in case the driver can accommodate these
additional IEs.
Bug: http://lists.infradead.org/pipermail/hostap/2022-January/040178.html
Bug-Debian: https://bugs.debian.org/1004524
Bug-ArchLinux: https://bugs.archlinux.org/task/73495
Upstream-Status: Changes Requested [https://patchwork.ozlabs.org/project/hostap/patch/20220130192200.10883-1-mail@david-bauer.net]
Reported-by: Étienne Morice <neon.emorice@mail.com>
Tested-by: Étienne Morice <neon.emorice@mail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 6dca88aa4a)
CycloneDX is an open source standard developed by the OWASP foundation.
It supports a wide range of development ecosystems, a comprehensive set
of use cases, and focuses on automation, ease of adoption, and
progressive enhancement of SBOMs (Software Bill Of Materials) throughout
build pipelines.
So lets add support for CycloneDX SBOM for packages and images
manifests.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit d604a07225)
There is no standard for ABI versioning, so its not possible to find out
from `libext2fs2`, `libiwinfo20230701` or `libss2` package names if
thats just package name or package name with ABI version included. To
help with the decision, lets make ABI version aviable in package index.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 649655f427)
Common Platform Enumeration (CPE) is a structured naming scheme for
information technology systems, software, and packages.
In order for the information to be processed further, it should also be
available in JSON package manifests.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 8562c65ff8)
Common Platform Enumeration (CPE) is a structured naming scheme for
information technology systems, software, and packages.
In order for the information to be processed further, it should also be
available in package index files.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(cherry picked from commit 33b3fea702)
Remove ABI version, since its format is not accepted by the linker.
Enable rpath to avoid clash with system libraries
Signed-off-by: Felix Fietkau <nbd@nbd.name>
(cherry picked from commit 5eb8a21ba5)
DT binding for MAC cells in fixed layout was upstream approved and
accepted. Add support for it. This can replace quite some of our
downstream hacks.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 61f674df4f)
It must read the entire image for previous code of 'imsz' or 'imszb'.
Signed-off-by: Jianhui Zhao <zhaojh329@gmail.com>
Suggested-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 3bbc1d5fba)
Add build for the MTK3943 reference board for MT7981B+MT7976C.
**Hardware specification:**
- SoC: MediaTek MT7981B 2x A53
- Flash: various options
- RAM: 256MB DDR3
- Ethernet: 4 x 10/100/1000 Mbps via MT7531AE switch
EITHER 1 x 10/100/1000 Mbps built-in PHY
OR 1 x 10/100/1000/2500 Mbps MaxLinear GPY211C
- Switch: MediaTek MT7531AE
- WiFi: MediaTek MT7976C
- Button: RST, WPS
**Flash instructions for SPIM-NAND:**
- write *mt7981-rfb-spim-nand-preloader.bin to 'BL2' partition
- write *mt7981-rfb-spim-nand-bl31-uboot.fip to 'FIP' partition
- erase 'ubi' partition
- reset board
- create ubootenv and ubootenv2 UBI volumes in U-Boot
- edit environment and set bootcmd, e.g.
setenv bootconf 'config-1#mt7981-rfb-spim-nand#mt7981-rfb-mxl-2p5g-phy-eth1'
setenv bootcmd 'ubi read $loadaddr fit; bootm $loadaddr#$bootconf'
- load initramfs image via TFTP:
setenv serverip 192.168.1.254
setenv ipaddr 192.168.1.1
setenv bootfile openwrt-mediatek-filogic-mediatek_mt7981-rfb-initramfs.itb
saveenv ; saveenv
tftpboot
bootm $loadaddr#$bootconf
- Now use sysupgrade to write OpenWrt firmware to flash.
SNFI-NAND, SPIM-NOR and eMMC all work very similar, a bootable SD card image
is also being generated. However, as the board I've been provided only comes
with SPIM-NAND all other boot media are untested.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit ce7209bd21)
Improve and package builds for various boot media configurations of the
MediaTek MT7981 reference board.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 8428bed15d)
When adding builds for MT7981 the related Makefile sections for MT7986
have apparently been copied, but in one instance the rename from 7986 to
7981 has been omitted. Fix that now.
Fixes: 602cb4f325 ("arm-trusted-firmware-mediatek: add build for MT7981 DDR3")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit be6e257fe6)
UARTs not used as boot console are currently broken on some MediaTek
targets due to register access depending on the bus clock being enabled.
Add patch to make sure this dependency is always met.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
(cherry picked from commit 9f62abbb60)
The code for hostapd-mbedtls did not work when used for OWE association.
When handling association requests, the buffer offsets and length
assumptions were incorrect, leading to never calculating the y point,
thus denying association.
Also when crafting the association response, the buffer contained the
trailing key-type.
Fix up both issues to adhere to the specification and make
hostapd-mbedtls work with the OWE security type.
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 39341f422f)
Due to circuit issue or silicon defect, sometimes the WiFi switch button
of the Archer C7 v2 can be accidentally triggered multiple times in one
second. This will cause WiFi to be unexpectedly shut down and trigger
'irq 23: nobody cared'[1] warning. Increasing the key debounce interval
to 1000 ms can fix this issue. This patch also add the missing rfkill
key label.
[1] Warning Log:
```
[87765.218511] irq 23: nobody cared (try booting with the "irqpoll" option)
[87765.225331] CPU: 0 PID: 317 Comm: irq/23-keys Not tainted 5.15.118 #0
...
[87765.486246] handlers:
[87765.488543] [<85257547>] 0x800c29a0 threaded [<5c6328a2>] 0x80ffe0b8 [gpio_button_hotplug@4cf73d00+0x1a00]
[87765.498364] Disabling IRQ #23
```
Fixes: https://github.com/openwrt/openwrt/issues/13010
Fixes: https://github.com/openwrt/openwrt/issues/12167
Fixes: https://github.com/openwrt/openwrt/issues/11191
Fixes: https://github.com/openwrt/openwrt/issues/7835
Tested-by: Hans Hasert
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit e32f70e706)
HiWiFi HC5861 has a GbE port which connected to the RTL8211E PHY
chip. This patch adds the missing Realtek PHY driver package and
sets the correct external PHYs base address to make it work again.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
(cherry picked from commit f025135f16)
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xc22): relocation R_MIPS16_26 against `libxt_DNAT_init' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol printf
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
(cherry picked from commit 5dbdf3bb3a)
This fixes building with USE_LTO enabled.
<artificial>:(.text+0xcc8): relocation R_MIPS16_26 against `luaL_argerror' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
(cherry picked from commit 246b97b607)
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x4194): relocation R_MIPS16_26 against `cil_printf.lto_priv.0' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol memcmp
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
(cherry picked from commit 1925a183a3)
This fixes building with USE_LTO enabled:
<artificial>:(.text.exit+0x6e): relocation R_MIPS16_26 against `pthread_key_delete' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol stpcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
(cherry picked from commit 2a33d26d21)
This fixes building with USE_LTO enabled.
<artificial>:(.text+0x400c): relocation R_MIPS16_26 against `iwinfo_close' cannot be used when making a shared object; recompile with -fPIC
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: non-dynamic relocations refer to dynamic symbol strcpy
./openwrt/staging_dir/toolchain-mips_24kc_gcc-12.3.0_musl/lib/gcc/mips-openwrt-linux-musl/12.3.0/../../../../mips-openwrt-linux-musl/bin/ld.bfd: failed to set dynamic section sizes: bad value
collect2: error: ld returned 1 exit status
Signed-off-by: Anari Jalakas <anari.jalakas@gmail.com>
(cherry picked from commit fbacc5ae52)
Currently the zram default compressor choice is displayed whether or not
zram is activated. Since the default choice is lzo-rle, this adds a
false dependency on kmod-lib-lzo.
With this patch, the choice options appear only when activating zram.
Signed-off-by: Rani Hod <rani.hod@gmail.com>
(cherry picked from commit 62ada26de2)
This makes it possible to build the ipq807x netgear-wax218 without initramfs - which is required for downstream projects (gluon)
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
(cherry picked from commit b3d2008f92)
Commit 572ea68070 ("uboot-mediatek: add patches for MT7988 and
builds for RFB") renamed HSGMII to 2500basex, but forgot to update
the dts of Redmi Router AX6000, makes the network unusable.
This patch makes the network usable again.
Fixes: #13724
Fixes: 572ea68070 ("uboot-mediatek: add patches for MT7988 and builds for RFB")
Signed-off-by: Furong Xu <xfr@outlook.com>
(cherry picked from commit 03987d2d11)
Kernel 5.15 already supports the NanoPi R1 and NanoPi R1S H5,
and they use new LED bindings that do not match the existing
settings in 01_leds. Update led settings to fixes that.
List the led node on NanoPi R1S H5:
root@OpenWrt:~# ls /sys/class/leds/
green:lan green:wan red:status
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
(cherry picked from commit b25c7548e0)
