* ramips: increase HiWiFi HC5962 kernel partition to 4M
Increase kernel partition because 2M is insufficient for 4.19
Because the partition changes, previous version of OpenWrt cannot upgrade to this version
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: use all reserved space for HiWiFi HC5962
Idea was from ad6c6361f9 ("ath79: enable all space on Netgear ar9344-based WNDR routers")
These stock partitons: "backup", "hw_panic", "overly", firmware_backup", "opt"
do not contain any device-specific data and can be used for /overlay, resulting in
121M space
Users should erase those partitions with command `mtd erase <partition name>` prior to
upgrading to this version
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Co-authored-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* revert: ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control
revert: ramips: gsw_mt7621: disable PORT 5 MAC RX/TX flow control by default
This revert c8f8e59
The TX/RX flow control is not the cause of the TX timeouts issue
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: net/mediatek fix logical error
ramips: net/mediatek fix logical error
fe_empty_txd() should return `tx_ring_size - 1` on ring empty, and
return 0 on ring full.
* ramips: net/mediatek disable eee
ramips: net/mediatek disable eee
This disable eee for mt7530 ports, it causes the link down/up
issue, which happens when connecting to 100Mbit switch
Fixes: FS#1449
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add xiaomi_miwifi-r3 support
Specification:
- CPU: 580 MHz
- Flash size: 128 MiB NAND
- RAM size: 128 MiB DDR2
- Wireless No1: SoC-integrated: MT7620A 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Wireless No2: On-board chip: MT7612E 2x2 MIMO 802.11a/n/ac (5 GHz)
- Switch: MT7620 built-in 10/100 switch w/ vlan support
- USB: 2.0 x1
Flash instructions:
1. access ssh via https://wiki.openwrt.org/toh/xiaomi/mir3
2. in ssh:
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set uart_en=1
nvram commit
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-kernel1.bin kernel1
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-rootfs0.bin rootfs0
reboot
If you want to revert back to stock fw while on LEDE:
insert usb stick (FAT/FAT32) with stock fw renamed to miwifi.bin
fw_setenv flag_last_success 0
power off the device
hold the reset button and power on the device, keep holding the reset button until yellow led starts blinking.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add mt7620-nand driver for NAND flash
This add the mt7620-nand driver
and enable nand ubifs for subtarget mt7620
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
Co-authored-by: Chen Minqiang <ptpt52@gmail.com>
Specification:
- CPU: 580 MHz
- Flash size: 128 MiB NAND
- RAM size: 128 MiB DDR2
- Wireless No1: SoC-integrated: MT7620A 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Wireless No2: On-board chip: MT7612E 2x2 MIMO 802.11a/n/ac (5 GHz)
- Switch: MT7620 built-in 10/100 switch w/ vlan support
- USB: 2.0 x1
Flash instructions:
1. access ssh via https://wiki.openwrt.org/toh/xiaomi/mir3
2. in ssh:
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set uart_en=1
nvram commit
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-kernel1.bin kernel1
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-rootfs0.bin rootfs0
reboot
If you want to revert back to stock fw while on LEDE:
insert usb stick (FAT/FAT32) with stock fw renamed to miwifi.bin
fw_setenv flag_last_success 0
power off the device
hold the reset button and power on the device, keep holding the reset button until yellow led starts blinking.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
This bit is used to specify sdxc pinmap for mt76x8. Details available
in patch description.
To properly solve this problem and the other pinctrl hack in mtk-mmc
driver we'll need to write a dedicated pinctrl driver for mt76x8,
with the support for configuring AGPIO_MODE and RGCTL registers as
well as specially handling GPIO reservation/pinctrl setup for ESDMODE.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
Global attributes enable_mirror_tx/enable_mirror_rx depend on runtime
value of another global attribute mirror_source_port which just resides
in the memory
The same functionality can be achieved by directly setting port
attribute of the same names. E.g. the following two groups of commands
achieve the same thing
swconfig dev switch0 set mirror_source_port 3
swconfig dev switch0 set enable_mirror_tx 1
swconfig dev switch0 set mirror_source_port 4
swconfig dev switch0 set enable_mirror_tx 1
swconfig dev switch0 port 3 set enable_mirror_tx 1
swconfig dev switch0 port 4 set enable_mirror_tx 1
Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
