This creates a shared DTSI for qca955x Senao/Engenius APs with
concatenated firmware partition/okli loader:
- EAP1200H
- EnstationAC v1
To make this usable for future boards with 32 MB flash as well,
split the partitions node already.
Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These recipes and definitions can apply
to devices from other vendors
with PCB boards or SDK produced by Senao
not only the brand Engenius
possible examples:
Extreme Networks, WatchGuard, OpenMesh,
Fortinet, ALLNET, OCEDO, Plasma Cloud, devolo, etc.
so rename all of these items
and move DEVICE_VENDOR from common to generic/tiny.mk
Signed-off-by: Michael Pratt <mcpratt@pm.me>
This creates a shared DTSI for ar934x Senao/Engenius APs:
- EAP300 v2
- ENS202EXT v1
- EAP600
- ECB600
Since ar9341/ar9344 have different configuration, this new file
mostly contains the partitioning.
Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This creates a shared DTSI for ar724x Senao/Engenius APs:
- ENH202 v1
- EAP350 v1
- ECB350 v1
Since ar7240/ar7242 have different configuration, this new file
mostly contains the partitioning.
Suggested-by: Michael Pratt <mcpratt@pm.me>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The uart node is enabled on all devices except one (GL-USB150 *).
Thus, let's not have a few hundred nodes to enable it, but do not
disable it in the first place.
Where the majority of devices is using it, also move the serial0
alias to the DTSI.
*) Since GL-USB150 even defines serial0 alias, the missing uart
is probably just a mistake. Anyway, disable it for now so this
patch stays cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested on Pogoplug V4.
Linksys EA3500 will not build with buildbot settings and should be
disabled when the target is switched, unless the image size is
reduced again.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[add EA3500 comment]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Update config with make kernel_oldconfig.
CONFIG_SATA_PMP=y is added manually as done for 5.4.
This should be resolved properly in a separate issue.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[add back CONFIG_SATA_PMP, rebase/refresh]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
CONFIG_NET_DSA_MV88E6XXX_PTP was simply missing in generic config.
CONFIG_I2C_PXA_SLAVE was previously enabled via i2c-pxa package,
but got removed there without moving the symbol to generic config.
Fixes: dd13add3ce ("kernel: i2c-pxa: remove slave")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The kernel bump to 5.4 has removed the mx25l25635f hack, and the
mx25l25635f compatible is no longer required.
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
As suggested by Sergio, this adds GPIOs 19 and 8 explicitly into the
DIR-860L DTS, so the PCI-E ports get reset and the N radio (radio1)
on PCI-E port 1 comes up reliably.
Fixes the following error that popped up in dmesg:
[ 1.638942] mt7621-pci 1e140000.pcie: pcie1 no card, disable it (RST & CLK)
Suggested-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
Reviewed-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
This adds the necessary nuts and bolts for the uboot settings for both the ZyXEL GS1900-8HP v1 and v2.
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
The Netgear R6800 and R6700v2 devices have a Semtech SX1503 GPIO
expander controlling the device LEDs. This expander was initially
supported on 4.14, but support was lost in the transition to 5.4.
Since this driver cannot be built as a kernel module, enable it in the
kernel config for all mt7621 devices.
Run-tested on a Netgear R6800.
Cc: Stijn Segers <foss@volatilesystems.org>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Tested-by: Stijn Segers <foss@volatilesystems.org>
Marvell mv88e6xxx switch series cannot perform MAC learning from
CPU-injected (FROM_CPU) DSA frames, which results in 2 issues.
- excessive flooding, due to the fact that DSA treats those addresses
as unknown
- the risk of stale routes, which can lead to temporary packet loss
Backport those patch series from netdev mailing list, which solve these
issues by adding and clearing static entries to the switch's FDB.
Add a hack patch to set default VID to 1 in port_fdb_{add,del}. Otherwise
the static entries will be added to the switch's private FDB if VLAN
filtering disabled, which will not work.
The switch may generate an "ATU violation" warning when a client moves
from the CPU port to a switch port because the static ATU entry added by
DSA core still points to the CPU port. DSA core will then clear the static
entry so it is not fatal. Disable the warning so it will not confuse users.
Link: https://lore.kernel.org/netdev/20210106095136.224739-1-olteanv@gmail.com/
Link: https://lore.kernel.org/netdev/20210116012515.3152-1-tobias@waldekranz.com/
Ref: https://gitlab.nic.cz/turris/turris-build/-/issues/165
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Add symbol to generic config (this was added between 5.4 and 5.10),
and remove it from the targets where it was added by kernel_oldconfig
in the meantime.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
There are efforts underway to bring wireguard in-tree for Linux 5.4 and
to have a common build infrastructure for both 5.4 and 5.10 for
kmod-wireguard[0]. Until then, restrict kmod-wireguard to build only on
Linux 5.4, because the wireguard-compat package will not build on Linux
5.10.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Modify existing modules to reflect their new location in Linux 5.10. Add
missing dependenices.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
[enable CRYPTO_USER_API_ENABLE_OBSOLETE; add kmod-crypto-hash dependency
to usb-net-rtl8152]
Signed-off-by: David Bauer <mail@david-bauer.net>
Now that mirrors have picked it up, switch to using the @OPENWRT
mirror instead of hosting those files on Github.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Description:
1. From key and led config setting, we can find only "uartf" and "i2c" are used
as gpio by check mt7620 datasheet. It's time to remove unused pin group.
2. PSG1218 only have three led, so we can remove ethernet led pinctrl. refer to
Phicomm K2G.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
Keep 5.4 as stable until further validation.
Tested on Turris Omnia (Rui Salvaterra) and ESPRESSObin v5 (Tomasz
Maciej Nowak). Cortex-A{53,72} subtargets are only build-tested.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[added comment about tests]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enable and fix hardware buffer management. Also fix the IRQ storm caused by a
misconfiguration of the PCA9538 interrupt pin.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Make each logical patch group numbering contiguous.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[add kernel version to backport]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Also delete already upstreamed patches/changes.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Just a simple copy, no refresh yet.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[do not duplicate files]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove the implicit/inherited symbols. While not strictly necessary, this will
make reviewing the diff between 5.4 and 5.10 easier.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
This will make the specific kconfig smaller.
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Tested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[improved commit title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current driver has some troubles:
- Some groupings are wrong.
- The pinctrl group0 owns pins never used (at least in Openwrt) for any
pinmux. The driver hijacks all the pins on the group avoiding any other
use, spite they're free. I.e. for buttons, causing this kernel error:
[ 4.735928] gpio-keys-polled keys: unable to claim gpio 479, err=-22
[ 4.742642] gpio-keys-polled: probe of keys failed with error -22
- Minor errors about groupings on the documentation
- Missing "diag" grouping in dtsi
- Wrong groupings in dtsi
Fix it by setting the correct groups.
And relax the pin capturing, letting the gpios belonging to any group to
be used for other purposes like buttons. This was the behavior with stock
firmwares and old OpenWrt versions which never caused any trouble.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
IMAGE_NAME is set twice for ventana, and the second value
actually matches the default in image.mk. Remove both.
Fixes: ded905ce43 ("imx6: extend cubox support to hummingboard,
add support for building full images")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The lan port sequence was reversed compared to the labels.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The aliases node is expected as one of the first entries, and
having it there matches alphabetic sorting as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
These were redefines of the same value already set in the SoC dtsi
files.
Reported-by: Shiji Yang <yangshiji66@qq.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Phicomm K2G:
add missing label_mac
Phicomm PSG1218A & PSG1218B:
The previous wan mac was set as factory@0x28 +1 (originally based
on the default case for the ramips target), but the correct wan mac
is factory@0x28 -1, being equal to factory@0x2e.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like done for several targets already, splitting base-files into
subtarget will provide smaller images due to more specific
distribution of files per subtarget and allow to use default cases
more effectively.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
IPSEC needs a reset before using its HW RNG.
Otherwise, the numbers generated won't be random at all.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This target has full device tree support, thus reducing the number of
patches needed for bcm63xx, in which there's a patch for every board.
The intention is to start with a minimal amount of downstream patches and
start upstreaming all of them.
Current status:
- Enabling EHCI/OHCI on BCM6358 causes a kernel panic.
- BCM63268 lacks Timer Clocks/Reset support.
- No PCI/PCIe drivers.
- No ethernet drivers.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Since there are only 16 characters available, on most cases the vendor name
will fit in the metadata, but the model name won't fit.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
