The TPLink CPE devices CPE210/CPE510 based on ar9344 have a build-in
Low Noise Amplifier on both of the 2x2 mimo rx chains.
This patch activates those two LNAs in the respective receiving chains
and hence improves the RX sensitivity by about 20dB.
Tested on CPE510 v2 & v3.
Signed-off-by: Thomas Huehn <thomas.huehn@hs-nordhausen.de>
Acked-by: Robert Marko <robimarko@gmail.com>
d6bd1047d004 vlandev: dump vlan id in device status
e0c838bd06a6 vlandev: support bridge-vlan aliases in the vid config parameter
574dc4a17105 system-dummy: print configured mac address
14f0e8ff928f system-linux: simplify mask check in system_if_apply_settings
524310276f20 system-linux: move device settings handling to device.c
42c48866f1c1 config: parse default mac address from board.json
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In this new setup the switch is treated as wan, lan1.100 is used as
our mgmt vlan.
The board mac is applied to eth0, switch and switch.1
The board mac is assigned with the LA bit set to all lan ports while
incrementing it.
Signed-off-by: John Crispin <john@phrozen.org>
Add code for setting mac addresses inside board.json and rendering
them out to uci. On switches we want to have a unique MAC on each port.
With 48 port switches that would require 48 device sections in
/etc/config/network. Doing so via board.json is easier.
Signed-off-by: John Crispin <john@phrozen.org>
Because the bug described in FS#2428 has been fixed with bf2870c1d9
("kernel: fix mtd partition erase < parent_erasesize writes") these
devices can now safely do sysupgrade.
Restore sysupgrade support disabled in:
0cc87b3bac ("ath79: image: disable sysupgrade images for routerstations
and ja76pf2")
cc5256a8bf ("ath79: base-files: disable sysupgrade for routerstations
and ja76pf2")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[move Build block, remove check-size argument, wrap sysupgrade line,
make commit message easier to read]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch fixes build of squashfs image on lantiq. Currently the FEATURE
variable is overwritten by the subtarget.
Fixes: FS#3480
Fixes: f1c6523376 ("lantiq: clean up target/subtarget features")
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
[reformat Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specifications:
SoC: MediaTek MT7621ST (880 MHz)
FLASH: 16 MiB (Macronix MX25L12835FM2I-10G)
RAM: 128 MiB (Nanya NT5CB64M16FP-DH)
WiFi: MediaTek MT7603EN bgn 2x2:2
WiFi: MediaTek MT7612EN an 2x2:2
BTN: Reset, WPS
LED: - Power
- WiFi 2.4 GHz
- WiFi 5 GHz
- WAN
- LAN {1-4}
- USB {1-2}
UART: UART is present as pin hole next to the aluminium capacitor.
3V3 - RX - GND - TX / 115200-8N1
3V3 is the nearest on the aluminium capacitor and nut hole (pin1).
USB: 2 ports
POWER: 12VDC, 1.5A (Barrel 5.5x2.1)
Installation:
Via TFTP:
Set your computers IP-Address to 192.168.1.75
Power up the Router with the Reset button pressed.
Release the Reset button after 5 seconds.
Upload OpenWRT sysupgrade image via TFTP:
tftp -4 -v -m binary 192.168.1.1 -c put IMAGE
MAC addresses:
0x4 *:98 2g/wan, label
0x22 *:9c
0x28 *:98
0x8004 *:9c 5g/lan
Though addresses are written to 0x22 and 0x28, it appears that the
vendor firmware actually only uses 0x4 and 0x8004. Thus, we do the
same here.
Signed-off-by: Pavel Chervontsev <cherpash@gmail.com>
[add MAC address overview, add label-mac-device, fix IMAGE_SIZE]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
All firmwares were added to linux-firmware, so there's no need to keep this
package definitions.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Instead of duplicating board firmware binaries, which are exactly the same
as the ones from linux-firmware, add dependencies and remove duplicated
downloads.
Runtime-tested on ath79 (TP-Link Archer C7 v2) and ipq806x (Netgear R7800).
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Split ath10k firmwares into board and firmware packages.
This way we can add dependencies to ath10k-ct firmware packages.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
It is impossible to locate package that failed the build just from log
once more build is run in parallel (that is more than one make job). The
only way is to scout log files for failed package going back trough log.
This change makes it so error is printed for package that failed every
time.
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
Fixup dfa357a3de "mvebu: base-files: Update Turris Omnia U-Boot
environment" which should have included this file as well.
By rebasing the initial patch this file somehow disappeared.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia)
[explain fixup in commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
It seems like after a build the /dl dir seems to now contain a .hash
file for each source file due to inproper cleanup so fix it by removing
those intermediate files before leaving the download action.
Fixes: 4e19cbc553 ("download: handle possibly invalid local tarballs")
Reported-by: Hannu Nyman <hannu.nyman@iki.fi>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
rules.mk always passes these as -I/-L to the toolchain.
Fixes rare errors like:
cc1: error: staging_dir/target-aarch64_cortex-a53_musl/usr/include: No such file or directory [-Werror=missing-include-dirs]
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Paul Spooren <mail@aparcar.org>
Acked-by: Rosen Penev <rosenp@gmail.com>
Without this, cmake will use whatever CC/CXX is set to, which could be
clang. In that case, at least libjson-c/host will fail to compile.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Currently the check target fails if the kernel Git tree is used:
$ make toolchain/kernel-headers/{download,check}
make[2]: Entering directory 'toolchain/kernel-headers'
Makefile:105: *** ERROR: Unknown pack format for file openwrt/tmp/dl/. Stop.
make[2]: Leaving directory 'toolchain/kernel-headers'
toolchain/Makefile💯 recipe for target 'toolchain/kernel-headers/check' failed
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Currently it's assumed, that already downloaded tarballs are always
fine, so no checksum checking is performed and the tarball is used even
if it might be corrupted.
From now on, we're going to always check the downloaded tarballs before
considering them valid.
Steps to reproduce:
1. Remove cached tarball
rm dl/libubox-2020-08-06-9e52171d.tar.xz
2. Download valid tarball again
make package/libubox/download
3. Invalidate the tarball
sed -i 's/PKG_MIRROR_HASH:=../PKG_MIRROR_HASH:=ff/' package/libs/libubox/Makefile
4. Now compile with corrupt tarball source
make package/libubox/{clean,compile}
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Move the update procedure from sysupgrade to first boot, which is much
more convenient in the sysupgrade case (otherwise the environment is
always one generation behind).
Check whether we have an old U-Boot release installed, and update the
environment only if necessary.
Some notes on the U-Boot environment:
The first 9 lines are a copy of the default environment of the old U-Boot
release - only modified, to run "distro_bootcmd", in case "mmcboot" fails
to boot the factory OS.
The remaining 16 lines are a backport of the default environment of the
new U-Boot release (shipped with CZ11NIC23). The main entry point is
"distro_bootcmd", which eventually sources boot.scr. This way, we have
a unified boot protocol for all Turris Omnia revisions so far.
This commit also fixes a shortcoming of previous Turris Omnia support:
Users may install OpenWrt with the Turris Omnia in factory state
(i.e. invalid environment store). In that case, neither fw_setenv, nor
U-Boot itself, would import the default environment from the image -
screwing up the rescue system, at least!
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia)
In contrast to the U-Boot version shipped with older versions of Turris
Omnia (CZ11NIC13, CZ11NIC20), the version shipped with Turris Omnia 2019
(CZ11NIC23) relies on the existence of /boot.scr.
Consequently, add a suitable boot script to the sysupgrade image.
Flash instructions for Turris Omnia 2019:
- Download openwrt-...-sysupgrade.img.gz, gunzip it, and copy the resulting
.img file to the root of a USB flash drive (FAT32 or ext2/3/4).
- Enter a rescue shell: Either via 5-LED reset and ssh root@192.168.1.1
on LAN port 4, or via 7-LED reset and the serial console.
- Insert the USB drive and mount it:
mkdir /mnt; mount /dev/sda1 /mnt
- Flash the OpenWrt image to eMMC:
dd if=/mnt/openwrt-...-sysupgrade.img of=/dev/mmcblk0 bs=4096 conv=fsync
- Reboot.
Flash instructions using a temporary "medkit" installation were written for
the older versions of Turris Omnia, and will *not* work on the Turris Omnia
2019.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Silence the warning in git 2.27 about undefined fast-forward style
in git pull. Define "ff-only" as the style.
Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
When setting the option IPK_FILES_CHECKSUMS the build system stores
checksums of all package file as metadata. In combination with pkg_check
this allows to see if a package is broken, e.g. caused by bad flash.
To create those checksums the tool `sha256sum` were used while the rest
of OpenWrt uses `mkhash`, a small & fast implementation of sha256. As
the build system does not check the existence of `sha256sum` and the
stderr output is moved to /dev/null, a situation where the option is
enabled but no actual checksum are created may occur.
Instead of adding `sha256sum` as a requirement, this replaces it with
`mkhash sha256` and adapts the `sed` pipe command to fit spacing.
CC: Xu Wang <xwang1498@gmx.com>
CC: Michal Hrusecky <Michal@Hrusecky.net>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Hauke wrote:
> We want to run some processes in the procd-ujail, this works when we
> use a SquashFS image and an overlay file system, but when we use an
> initramfs it does not work.
> [...]
> When we switch from initramfs to tmpfs, it is working, we added this
> code to target/linux/generic/other-files/init to make [it] work.
Move files to newly mounted tmpfs and then use switch_root to chroot
into new rootfs and free initramfs.
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Drop our local sstrip copy and use the current ELFKickers upstream
version.
Patch the original makefile in order to avoid building elftoc, since it
fails with musl's elf.h. This is fine, since we only need sstrip anyway.
Finally, add the possibility to pass additional arguments to sstrip and
pass -z (remove trailing zeros) by default, which matches the behaviour
of the previous version.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
[shorten long commit msg lines]
Signed-off-by: Paul Spooren <mail@aparcar.org>
- Removed following patches:
100-strip_charsets.patch - makes the full variant slim.
101-autotools.patch - this one fails to apply because it was backported
from newer versions for 1.11.1.
103-configure_ac_fix.patch - backported from newer versions
200-work-with-libtool2.patch - is not needed anymore, it is done
differently in upstream
300-fortify-source-compat.patch - these files are not there anymore
- TVHeadend requires working iconv library e.g. transliteration to ASCII
and this does not work with libiconv-full currently.
There is a simple test, which requires to install iconv package.
Before applying this update:
root@turris:/# echo ŽluťoučkýKůň | iconv -t ASCII//TRANSLIT//IGNORE
luoukK
After applying this update:
root@turris:~# echo ŽluťoučkýKůň | iconv -t ASCII//TRANSLIT//IGNORE
Zlutouck'yKun
- Makefile changes:
Use HTTPS for their website
Fixed deprecated SPDX License Identifier
Move PKG_MAINTAINER above PKG_LICENSE
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Tested-by: Rosen Penev <rosenp@gmail.com> [malta]
compiler warns that exit() isn't defined so checks for build system
compiler fail.
include <stdlib.h> to define exit()
Tested under macos Catalina & Big Sur
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
Recent kernel bumps & target patch refactors have left some patch fuzz
around. Refreshed kernel patches using update_kernel script.
Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
