If an external module uses exported symbols from another external
module, Kbuild needs to have full knowledge of all symbols to
avoid spitting out warnings about undefined symbols.
Use PKG_EXTMOD_SUBDIRS to point to the build directory which contains
the Module.symvers.
Pass KERNEL_MAKE_FLAGS to the external module build, to inject
KBUILD_EXTRA_SYMBOLS. KBUILD_EXTRA_SYMBOLS holds a space separated list
of Module.symvers, which list all exported symbols.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.
Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.
Fixes FS#3624
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Included:
- Hack for support MTWiFi
- HWRNG driver for RK3328 & RK3399
- Fix for hot reboot
- I2C screen support for NanoPi R2S
- Overclocking support for RK3328 and NanoPi4 series
- Ethernet compat node for NanoPi R2S
- Support for NanoPi R4S
Minor adjustments:
- Used r8169 driver for NanoPi R4S by default as r8168 is broken on newer kernel
Refreshed all patches.
Reviewed-by: AmadeusGhost <amadeus@project-openwrt.eu.org>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Remove all upstreamed patches and add the kernel configuration for
version 5.10.
The Rock Pi 4 was split in multiple versions. Add a DTS with the old
name in order to keep compatibility while having kernel 5.4 and 5.10 in
parallel. Switch to the Rock Pi 4A DTS once Kernel 5.4 support is
removed.
Tested-on: Nanoi R2S
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: AmadeusGhost <amadeus@project-openwrt.eu.org>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
When recursively deleting partitions, don't acquire the masters
partition lock twice. Otherwise the process endy up in a deadlocked
state.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch
UART
----
CPU UART0 at the pinout next to the Holtek MCU.
Pinout (first pin next to SoC / MCU)
0 3V3
1 RX
2 TX
3 GND
Settings are 115200 8N1.
Opening the case
----------------
Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.
Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Transfer the OpenWrt sysupgrade image to the device using SCP.
3. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
4. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6
5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock8
$ dd if=openwrt.bin of=/dev/mtdblock9
6. Reboot the device. It should boot into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.
This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
Compile and runtime-tested on mediatek/mt7622
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Kernel has changed the of_get_phy_mode API in commit 0c65b2b90d13
("net: of_get_phy_mode: Change API to solve int/unit warnings").
This is already included in kernel 5.5, so fix the version switch
(though this will not actually matter for the versions we support).
Similar driver adjustments to account for the API change will
probably be necessary to various other local drivers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
This patch has been added to 5.4, but not been copied to 5.10:
7495acb555 ("kernel: backport mtd commit converting partitions doc syntax")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Reapply changes added to 5.4 but not copied to 5.10:
3da4acaa7b ("kernel: fix busy wait loop in mediatek PPE code")
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.
time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
This applies another patch from 5.4 to 5.10 as well:
de09355f74 ("kernel/hack-5.4: make UDP tunneling user-selectable")
UDP tunneling support isn't user-selectable, but it's required by WireGuard
which is, for the time being, an out-of-tree module. We currently work around
this issue by selecting an unrelated module which depends on UDP tunnelling
(VXLAN). This is inconvenient, as it implies this unrelated module needs to be
built-in when doing a monolithic build.
Fix this inconvenience by making UDP tunneling user-selectable in the kernel
configuration.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
This is needed for linux 5.10, where modules.builtin is generated from
vmlinux.o
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Tianling Shen <cnsztl@project-openwrt.eu.org>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
After the ABI version rework, packages need to be declared in the order of their
dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Tianling Shen <cnsztl@project-openwrt.eu.org>
After the ABI version rework, packages need to be declared in the order of
their dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Tianling Shen <cnsztl@project-openwrt.eu.org>
This allows using the last integrated PHY (and so e.g. WAN port on the
ASUS GT-AC5300).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Tianling Shen <cnsztl@project-openwrt.eu.org>
Stability of this Ethernet driver has been a long-standing issue, with
many people reporting frequent "transmit queue timeouts" and even
occasional crashes.
Disabling TSO in the driver helps with stability, although it is likely a
workaround and might not fix the issue completely.
There is a slight slowdown in forwarding performance for TCP packets
(75 kpps vs. 80 kpps with comparable CPU utilization), but this is still
enough to forward close to 1 Gbit/s of full-sized packets across multiple
flows.
Master is using a different ethernet driver, so this is not a backport.
Because of this different driver, the upcoming 21.02 release does not seem
to be affected by these stability issues.
Thanks to mrakotiq for the initial patch.
Fixes: FS#2628
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Signed-off-by: Tianling Shen <cnsztl@project-openwrt.eu.org>
The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
Fixes: FS#2086
The logic for IS_TTY was broken, because it was testing stdin
instead of stdout.
MAKE_TERMOUT was introduced in GNU Make version 4.1 (05 Oct 2014),
so it should be available everywhere nowadays.
Signed-off-by: R. Diez <rdiezmail-openwrt@yahoo.com>
FS#2086 "IS_TTY in the makefile is broken" reports flawed detection of
stdout piping to a file. The issue describes how e.g. terminal color
codes and up in log files if running make like `make > log.txt`.
The proposed solution uses the make variable "MAKE_TERMOUT", which was
introduced in make 4.1. All major distributions seem to updated to 4.1
or later, so this ideally dosen't break anything.
Signed-off-by: Paul Spooren <mail@aparcar.org>
After the ABI version rework, packages need to be declared in the order of
their dependencies, so that dependent packages will use the right ABI version
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This was accidentally dropped in 27a4a71c24
("metadata: handle ABI version rebuild tracking for transient dependencies")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This reverts commit b12288fa69.
The patchelf approach is too fragile, and the only users of this have been
converted to make patching unnecessary
Leave the abi_version_str variable in place in rules.mk
Signed-off-by: Felix Fietkau <nbd@nbd.name>
