3023b0cc7352 bridge: add support for defining port member vlans via hotplug ops
a3016c451248 vlan: add pass-through hotplug ops that pass the VLAN info to the bridge
d59f3ddcbaf0 vlandev: add pass-through hotplug ops that pass the VLAN info to the bridge
dd5e61153636 bridge: show vlans in device status
a56e14afa612 bridge: preserve hotplug ports on vlan update if config is unchanged
d1e8884f8911 bridge: fix use-after-free bug on bridge member free
3a2b21001c3c system-dummy: set present state only for simple devices
ed11f0c0ffe4 bridge: only overwrite implicit vlan assignment if vlans are configured
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The original patch from QCA over rode the nf_conntrack_un/register_notifier API, which
will break other modules relying on the API. Reworked the notification APIs to play nice
with others.
This patch adds support for D-Link DIR-2640 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 256 MB (DDR3)
* Flash: 128 MB (NAND)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WPS
* LEDs: Power (blue/orange), Internet (blue/orange), WiFi 2.4G (blue),
WiFi 5G (blue), USB 3.0 (blue), USB 2.0 (blue)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
MAC addresses:
lan factory 0xe000 *:a7 (label)
wan factory 0xe006 *:aa
2.4 factory 0xe000 +1 *:a8
5.0 factory 0xe000 +2 *:a9
Seems like vendor didn't replace the dummy entries in the calibration data.
Signed-off-by: James McGuire <jamesm51@gmail.com>
[fix device definition title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Allow configuring ipsets with dedicated config sections:
config ipset
list name 'ss_rules_dst_forward'
list name 'ss_rules6_dst_forward'
list domain 't.me'
list domain 'telegram.org'
instead of current, rather inconvenient syntax:
config dnsmasq
...
list ipset '/t.me/telegram.org/ss_rules_dst_forward,ss_rules6_dst_forward'
Current syntax will still continue to work though.
With this change, a LuCI GUI for DNS ipsets should be easy to implement.
Signed-off-by: Aleksandr Mezin <mezin.alexander@gmail.com>
Signed-off-by: Hans Dedecker <dedeckeh@gmail.com> [PKG_RELEASE increase]
Manually rebased patches:
bcm27xx:
patches-5.4/950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch
bcm53xx:
patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
layerscape:
patches-5.4/802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
patches-5.4/808-i2c-0002-MLK-10893-i2c-imx-add-irqf_no_suspend.patch
patches-5.4/820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch
Removed since could be reverse-applied by quilt:
mediatek:
patches-5.4/0700-arm-dts-mt7623-add-missing-pause-for-switchport.patch
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86_64
Run-tested: ipq806x/R7800, x86_64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64]
Rebase of 802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
Due to the use of LD_LIBRARY_PATH, the programs running in the fakeroot
environment may end up loading bundled SDK libraries using the system
ld.so.
Rework the relocatability patch to avoid meddling with LD_LIBRARY_PATH
and construct the paths to faked and libfakeroot.so directly.
Fixes: f93cb5c2c8 ("fakeroot: make fakeroot script relocatable")
Reviewed-by: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
This adds a variant of refpolicy that builds the modular form of the
policy. While this requires more memory on the target device, along with
some tricks to deal with OpenWrt's volatile /var directory, it is useful
for experiementing with SELinux policy.
Signed-off-by: W. Michael Petullo <mike@flyn.org>
Without an absolute path to staging_dir/host/bin/sstrip the Makefile
tries to run a host installed version of sstrip, which is likely not
available.
Signed-off-by: Paul Spooren <mail@aparcar.org>
mkhash currently returns the hash of an empty input when trying to hash
a folder. This can be missleading in caseswhere e.g. an env variable is
undefined which should contain a filename. `mkhash ./path/to/$FILE`
would exit with code 0 and return a legit looking checksum.
A better behaviour would be to fail with exit code 1, which imitates the
behaviour of `md5sum` and `sha256sum`.
To avoid hashing of folders the `stat()` is checked.
Hashing empty inputs result in the following checksums:
md5: d41d8cd98f00b204e9800998ecf8427e
sha256: e3b0c44298fc1c149afbf4c8996fb92427ae41e4649b934ca495991b7852b855
Signed-off-by: Paul Spooren <mail@aparcar.org>
If hashing a file fails mkhash shouldn't just silently fail. Now check
after each call of `hash_file()` the return and exit early in case of
errors. The return value which was previously ignored and would always
return 0.
Signed-off-by: Paul Spooren <mail@aparcar.org>
The -n option prints the filename of hashed files next to the calculated
checksum. Reflect that in the usage message.
user@dawn:~/src/openwrt/openwrt$ ./a.out md5 -n .config
eb06db36e7b6751cb18801945e46bf5d .config
Signed-off-by: Paul Spooren <mail@aparcar.org>
Althought most of the switches aren't routers, they can be used as such,
so let's add some of the packages from the router's DEVICE_TYPE. While
at it, remove swconfig package which is not needed on DSA targets.
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixes following dtc warning:
../dts/rtl838x.dtsi:38.3-145.3: Warning (reg_format): /: Root node has a "reg" property
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Hardware specification
----------------------
* RTL8382M SoC, 1 MIPS 4KEc core @ 500MHz
* 128MB DRAM
* 32MB NOR Flash (MX25L25635E)
* 24 x 10/100/1000BASE-T ports
- Internal PHY with 8 ports (RTL8218B)
- Two external PHYs with 8 ports each (RTL8218B)
* 4 x Gigabit RJ45/SFP Combo ports
- External PHY with 4 SFP ports (RTL8214FC)
* Power LED
* Reset button on front panel
* UART (115200 8N1) via unpopulated standard 0.1" pin header marked J6
UART pinout
-----------
[oooo]J3 [o]ooo|J6
| ^ ||`------ GND
| | |`------- RX
| | `-------- TX
| `---------- Vcc (3V3)
|
`------------------ J3 is power input connector nearby J6 UART
Boot initramfs image from U-Boot
--------------------------------
1. Press Escape key during `Hit Esc key to stop autoboot` prompt
2. Press CTRL+C keys to get into real U-Boot prompt
3. Init network with `rtk network on` command
4. Load image with `tftpboot 0x8f000000 openwrt-rtl838x-generic-d-link_dgs-1210-28-initramfs-kernel.bin` command
5. Boot the image with `bootm` command
To install, upload the sysupgrade image to the OEM webpage or sysupgrade
from the system running from initramfs image.
It has been developed and tested on device with F1 revision.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
So the common bits can be easily shared with other boards in the family
and while at it add missing SPDX license identifiers into the DTS files
and fixed alphabetic sorting of the devices in the images.
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The D-Link DIR-645 currently uses an incorrect logic level for its
buttons.
Correct them in order to prevent unintentional activation of failsafe
mode.
Reported-by: Perry Melange <isprotejesvalkata@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 929e8f0f55)
The order of function and color in the labels in inverted for the
LAN LEDs. Fix it.
Fixes: 915966d861 ("ath79: Port PowerCloud Systems CAP324 support")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 96023cd4ba)
A lot of devices running OpenWrt x86 arch (32 or 64 bit) are either
"home-made routers" or devices that use PC class OEM components.
This commit enables OEM cards support on those devices by default.
Signed-off-by: Rafał Dzięgiel <rafostar.github@gmail.com>
[reformat commit message]
Signed-off-by: David Bauer <mail@david-bauer.net>
Building gdb failed with CONFIG_BUILD_NLS enabled. Use nls.mk and
add the necessary dependencies for libintl and libiconv.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
da9746a libopkg: clean up handling of unresolved dependencies
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Paul Spooren <mail@aparcar.org>
