8d5208f jail: fix false return in case of nofail mount
b41f76b procd: fix compile if procd-ujail is not selected
86a5105 jail: fs: fix build on uClibc-ng
bfce7d1 jail: fix some more mount options
268126a jail: add support for maskedPaths and readonlyPaths
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Split the /etc/uci-defaults/01_led_migration scripts into subtargets
as already done for most of the other base-files.
While this introduces a minor amount of code duplication, it still
is considered an improvement, as device-specific settings are kept
together in the subtargets' base-files and the script at hand can be
removed entirely for two of the subtargets not needing it.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This file is always present because it is part of the ltq-dsl-base
package on which these packages depend.
This check would not have been necessary in the past, because the script
was part of the TARGET_LANTIQ on which these packages also depend.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
It does not make sense to install this components on lantiq systems
where the dsl subsystem is not needed/used.
This also makes it possible to use the files also on other targets.
(hopefully ipq401x / FritzBox 7530 in the near future)
Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com>
For mt7621, console is set up via DTS bootargs individually in
device DTS/DTSI files. However, 44 of 74 statements use the
following setting:
chosen {
bootargs = "console=ttyS0,57600";
};
Therefore, don't repeat ourselves and move that definition to the SoC
DTSI file to serve as a default value.
This patch is cosmetic.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
update_kernel.sh refreshed all patches, no human interaction was needed
Build system: x86_64
Run-tested: Netgear R7800 (ipq806x)
Signed-off-by: John Audia <graysky@archlinux.us>
The last commit to this package that added the pkgconfig file did not
fix the paths to point to the prefix.
This allows packages to find lzo properly.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
The Helios 4 is a NAS from Kobol
that is powered by an Armada 38x
MicroSOM from Solidrun, similarly
to Clearfog.
This device has:
-Armada 38x CPU
(dual core ARMv7 1.6 Ghz)
-2 GB of ECC RAM
-Gigabit ethernet (Marvell)
-2x USB 3.0 ports
-4x Sata 3.0 ports
-i2c header (J9 |>GND|SDA|SCL|VCC)
-2x 3-pin fan headers with PWM
-micro-usb port is a TTL/UART to
USB converter connected to TTL
-MicroSD card slot
-System, 4xSata and 1xUSB LEDs
NOT WORKING: fan control
Fan Control requires a kernel patch
that is available in the Armbian
project (the "default firmware"
of this device) and named
mvebu-gpio-remove-hardcoded
-timer-assignment
This patch isn't acceptable
by OpenWrt, it should be upstreamed.
I also have that patch in my own
local OpenWrt builds,
in case you want a more
clean and less confusing patch
for upstreaming.
To install, write the disk image
on a micro SD card with dd or
win32 disk imager, insert the
card in the slot.
Check that the dip switch battery
for boot selection is as follows
Switch 1 and 2 down/off, switches
3, 4, 5 up/on.
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
Hardware
--------
RockChip RK3328 ARM64 (4 cores)
1GB DDR4 RAM
2x 1000 Base-T
3 LEDs (LAN / WAN / SYS)
1 Button (Reset)
Micro-SD slot
USB 2.0 Port
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card using
dd.
MAC-address
-----------
The vendor code supports reading a MAC address from an EEPROM connected
via i2c0 of the SoC. The EEPROM (address 0x51) should contain the MAC
address in binary at offset 0xfa. However, my two units didn't come with
such an EEPROM soldered on. The EEPROM should be placed between the SoC
and the GPIO pins on the board. (U10)
Generating rendom MAC addresses works around this issue. Otherwise, all
boards running the same image have identical MAC addresses.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add support for select a bootscript depending on the device built. This
is necessary, as the FriendlyARM NanoPi R2S needs a different bootcmd in
order to produce output on the debug UART.
Signed-off-by: David Bauer <mail@david-bauer.net>
This adds a function for generating a valid random MAC address (unset MC
bit / set locally administered bit).
It is necessary for devices which do not have a MAC address programmed
by the manufacturer.
Signed-off-by: David Bauer <mail@david-bauer.net>
Update the U-Boot to version v2020.07. Also replace the Makefile rewrite
with a proper patch, explaining why this hack is needed.
Run-tested: FriendlyARM NanoPi R2S
Signed-off-by: David Bauer <mail@david-bauer.net>
also install the firmware for all the supported boards
Signed-off-by: Lucian Cristian <lucian.cristian@gmail.com>
[fix ATF blob path in uboot-rockchip]
Signed-off-by: David Bauer <mail@david-bauer.net>
This patch adds support for D-Link DIR-867 A1 and D-Link DIR-882 A1. Given
the similarity of these devices, this patch also introduces a common DTS
shared between DIR-867 A1, DIR-878 A1 and DIR-882 A1.
Specifications:
* Board: AP-MTKH7-0002
* SoC: MediaTek MT7621AT
* RAM: 128 MB (DDR3)
* Flash: 16 MB (SPI NOR)
* WiFi: MediaTek MT7615N (x2)
* Switch: 1 WAN, 4 LAN (Gigabit)
* Ports: 1 USB 2.0, 1 USB 3.0
* Buttons: Reset, WiFi Toggle, WPS
* LEDs: Power (green/orange), Internet (green/orange), WiFi 2.4G (green),
WiFi 5G (green), USB 2.0 (green), USB 3.0 (green)
Notes:
* WiFi 2.4G and WiFi 5G LEDs are wired directly to the wireless chips
* DIR-867 wireless chips are limited to 3x3 streams at hardware level
* USB ports and related LEDs available only on DIR-882
Serial port:
* Parameters: 57600, 8N1
* Location: J1 header (close to the Reset, WiFi and WPS buttons)
* Pinout: 1 - VCC
2 - RXD
3 - TXD
4 - GND
Installation:
* D-Link Recovery GUI: power down the router, press and hold the reset
button, then re-plug it. Keep the reset button pressed until the power
LED starts flashing orange, manually assign a static IP address under
the 192.168.0.xxx subnet (e.g. 192.168.0.2) and go to http://192.168.0.1
* Some modern browsers may have problems flashing via the Recovery GUI,
if that occurs consider uploading the firmware through cURL:
curl -v -i -F "firmware=@file.bin" 192.168.0.1
Signed-off-by: Mateus B. Cassiano <mbc07@live.com>
[move DEVICE_VARIANT to individual definitions]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
