This adds a driver for the AW9523 I2C GPIO expander.
This driver is required to make LEDs as well as buttons on the Tenbay
T-MB5EU-V01 work.
This driver already had several upstream iterations. I'm working to
push this driver to mainline.
Ref: https://patchwork.ozlabs.org/project/linux-gpio/list/?series=226287
Signed-off-by: David Bauer <mail@david-bauer.net>
These boards have AR8327 or QCA8337 external ethernet switch.
The SOC also has it's own internal switch
where VLAN is now enabled by default.
Changes to preinit caused all switches to have VLANs enabled by default
even if they are not configured with a topology in uci_defaults
(see commit f017f617ae)
When both internal and external switches have VLANs,
and the external switch has both LAN and WAN,
the TX traffic from the SOC cannot flow to the tagged port on the external switch
because the VLAN IDs are not matching.
So disable the internal switch VLANs by default on these boards.
Also, add a topology for the internal switch,
so that on LuCI there is not an "unknown topology" warning.
In theory, it may be possible to have LAN ports on both switches
through internal and external PHYs, but there are no known boards that have this.
Signed-off-by: Michael Pratt <mcpratt@pm.me>
About the device
----------------
SoC: MediaTek MT7620a @ 580MHz
RAM: 64M
FLASH: 8MB
WiFi: SoC-integrated: MediaTek MT7620a bgn
WiFi: MediaTek MT7612EN nac
GbE: 2x (RTL8211F)
BTN: - WPS
- Reset
- Router/Repeater/AP (3-way slide-switch)
LED: - WPS (blue)
- 3-segment Wifi signal representation (blue)
- WiFi (blue)
- WAN (blue)
- LAN (blue)
- Power (blue)
UART: UART is present as Pads with through-holes on the PCB. They are
located next to the reset button and are labelled Vcc/TX/RX/GND as
appropriate. Use 3.3V, 57600-8N1.
Installation
------------
Using the webcmd interface
--------------------------
Warning: Do not update to the latest Wavlink firmware (version
20201201) as this removes the webcmd console and you will need to
use the serial port instead.
You will need to have built uboot/sqauashfs image for this device,
and you will need to provide an HTTP service where the image can
be downloaded from that is accessible by the device.
You cannot use the device manufacturers firmware upgrade interface
as it rejects the OpenWrt image.
1. Log into the device's admin portal. This is necessary to
authenticate you as a user in order to be able to access the
webcmd interface.
2. Navigate to http://<device-ip>/webcmd.shtml - you can access
the console directly through this page, or you may wish to
launch the installed `telnetd` and use telnet instead.
* Using telnet is recommended since it provides a more
convenient shell interface that the web form.
* Launch telnetd from the form with the command `telnetd`.
* Check the port that telnetd is running on using
`netstat -antp|grep telnetd`, it is likely to be 2323.
* Connect to the target using `telnet`. The username should
be `admin2860`, and the password is your admin password.
3. On the target use `curl` to download the image.
e.g. `curl -L -O http://<some-other-lan-ip>/openwrt-ramips-mt7620-\
wavlink_wl-wn579x3-squashfs-sysupgrade.bin`.
Check the hash using `md5sum`.
4. Use the mtd_write command to flash the image.
* The flash partition should be mtd4, but check
/sys/class/mtd/mtd4/name first. The partition should be
called 'Kernel'.
* To flash use the following command:
`mtd_write -r -e /dev/mtd<n> write <image-file> /dev/mtd<n>`
Where mtd<n> is the Kernel partition, and <image-file> is
the OpenWrt image previously downloaded.
* The command above will erase, flash and then reboot the
device. Once it reboots it will be running OpenWrt.
Connect via ssh to the device at 192.168.1.1 on the LAN port.
The WAN port will be configured via DHCP.
Using the serial port
---------------------
The device uses uboot like many other MT7260a based boards. To
use this interface, you will need to connect to the serial
interface, and provide a TFTP server. At boot follow the
bootloader menu and select option 2 to erase/flash the image.
Provide the address and filename details for the tftp server.
The bootloader will do the rest.
Once the image is flashed, the board will boot into OpenWrt. The
console is available over the serial port.
Signed-off-by: Ben Gainey <ba.gainey@googlemail.com>
Same hardware as Phicomm K2G but different flash layout.
Specification:
- SoC: MediaTek MT7620A
- Flash: 8 MB
- RAM: 64 MB
- Ethernet: 4 FE ports and 1 GE port (RTL8211F on port 5)
- Wireless radio: MT7620 for 2.4G and MT7612E for 5G, both equipped
with external PA.
- UART: 1 x UART on PCB - 57600 8N1
Flash instruction:
To avoid requiring UART for TFTP a dual flash procedure is suggested
to install the squashfs image:
1. Rename openwrt-ramips-mt7620-wavlink_wl-wn530hg4-initramfs-kernel.bin
to WN530HG4-WAVLINK.
2. Flash this file with the factory web interface.
3. With OpenWRT now running use standard sysupgrade to install the
squashfs image.
Signed-off-by: Nuno Goncalves <nunojpg@gmail.com>
[remove dts-v1, remove model from LED labels, wrap commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Device specifications:
* Model: Youku YK-L1/L1c
* CPU: MT7620A
* RAM: 128 MiB
* Flash: 32 MiB (YK-L1)/ 16 MiB (YK-L1c)
* LAN: 2* 10M/100M Ports
* WAN: 1* 10M/100M Port
* USB: 1* USB2.0
* SD: 1* MicroSD socket
* UART: 1* TTL, Baudrate 57600
Descriptions:
Previous supported device YOUKU yk1 is actually Youku YK-L1. Though they look
really different, the only hardware difference between the two models is flash
size, YK-L1 has 32 MiB flash but YK-L1c has 16MiB. It seems that YK-L1c can
compatible with YK-L1's firmware but it's better to split it to different models.
It is easy to identify the models by looking at the label on the bottom of the
device. The label has the model number "YK-L1" or "YK-L1c". Due to different flash
sizes, YK-L1c that using previous YK-L1's firmware needs to apply "force update"
to install compatible firmware, so please backup config file before system upgrade.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[use more specific name for DTSI]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MAC addresses read from official firmware
value location
Wlan xx 71 de factory@0x04
Lan xx 71 dd factory@0x28
Wan xx 71 df factory@0x2e
Label xx 71 dd factory@0x28
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[fix sorting in 02_network, redact commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Some targets select HZ=100, others HZ=250. There's no reason to select a higher
timer frequency (and 100 Hz are available in every architecture), so change all
targets to 100 Hz.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
1. rename led pin "air" to a more common name "wlan" and use "phy0tpt" to trigger it.
2. led "wan" can be triggered by ethernet pinctrl by default so just drop it.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
There are only two lan ports and one wan port on Youku yk1
Fixes: e9baf8265b ("ramips: add support for Youku YK1")
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[add Fixes:]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Enable testing kernel.
Delete upstreamed patches:
0098-disable_cm.patch can be dropped, upstream fixed CM handling.
Fix compile errors by using new kernel APIs.
Fix fuzz by manually editing patches to ensure the code goes in the
right place.
For 721-NET-no-auto-carrier-off-support.patch, revert upstream commit
a307593a6 to keep the OpenWrt ralink driver operational.
Add mt7621-pci-phy patch to select REGMAP_MMIO as discussed in PR #3693
and #3952.
Rename patches to follow the 3-digit classification from the OpenWrt
Developer Guide.
Run automatic quilt refresh.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
The lan port sequence was reversed compared to the labels.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[improve commit title/message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Phicomm K2G:
add missing label_mac
Phicomm PSG1218A & PSG1218B:
The previous wan mac was set as factory@0x28 +1 (originally based
on the default case for the ramips target), but the correct wan mac
is factory@0x28 -1, being equal to factory@0x2e.
Signed-off-by: Shiji Yang <yangshiji66@qq.com>
[minor commit title/message adjustments]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
While we mostly use the ucidef_set_led_* functions directly in 01_leds
we still have the set_wifi_led function in parallel for several old
devices. This is not only inconsistent with the other definitions,
it also links to the wlan0 interface instead of using a phy trigger
which would be independent of the interface name (and is used for
all newer devices anyway). Apart from that, the standard names
"wifi" and "wifi-led" are not very helpful in a world with different
radio bands either.
Thus, this patch removes the set_wifi_led function and puts the
relevant commands into the cases explicitly. This makes the
mechanism used more evident and will hopefully lead to some future
improvements or at least prevent some copy-pasting of the old
setups.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
On a platform with many very different devices, like found on ramips,
the generic profiles seem like remnants of the past that do not
have a real use anymore.
Remove them to have one thing less to maintain.
Actually, rt288x didn't have a default profile in the first place.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Acked-by: Paul Spooren <mail@aparcar.org>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
In ramips, it's not common to use an alias for specifying the WiFi
LED; actually only one device uses this mechanism (TL-WR841N v14).
Particularly since the WiFi LEDs are typically distinguished between
2.4G and 5G etc. it is also not very useful for this target.
Thus, this patch removes the setup lines for this mechanism and
converts the TL-WR841N v14 to the normal setup.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like in the previous patch for ath79 target, this will remove the
"devicename" from LED labels in ramips as well.
The devicename is removed in DTS files and 01_leds, consolidation
of definitions into DTSI files is done where (easily) possible,
and migration scripts are updated.
For the latter, all existing definitions were actually just
devicename migrations anyway. Therefore, those are removed and
a common migration file is created in target base-files. This is
actually another example of how the devicename removal makes things
easier.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
TP-Link Archer C5 v4 is a dual band router with 5 GbE ports
Advertised as AC1200 for its 867Mbps (2×2) 5GHz band
and 300 Mbps (2×2) 2.4GHz band.
Specs:
- SoC: MediaTek MT7620A
- Ethernet: 5 GbE ports (Realtek RTL8367S)
- Wireless 2.4GHz: MediaTek MT7620A
- Wireless 5GHz: MediaTek MT7612E
- RAM: 64MiB
- ROM: 8MiB (GD25Q64CSIG)
- 1 USB 2.0 port
- 2 Buttons (WPS and reset)
- 8 LEDs
Flash instructions:
Currently one has to install OpenWrt only via the serial console
1. Rename the factory.bin to to test.bin
2. start a TFTP server from IP address 192.168.0.225 and serve the image named test.bin
3. connect your device to the LAN port
4. power up the router and press 4 on the console to stop the boot process.
5. enter the following commands on the router console
tftp 0x80060000 test.bin
erase tplink 0x20000 0x7a0000
cp.b 0x80060000 0x20000 0x7a0000
reset
Signed-off-by: Deng Qingfang <dengqf6@mail2.sysu.edu.cn>
RT3x5x seems to work fine with kernel 5.4. Set the default kernel
version to 5.4 to bring this to a broader audience.
Since 4 of 6 targets are on kernel 5.4 now, invert the kernel
version setup logic in Makefile/target.mk files.
Tested on ZyXEL Keenetic.
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[invert version setup logic]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
MT7620 seems to work fine with kernel 5.4. Set the default kernel
version to 5.4 to bring this to a broader audience.
Tested on Archer C2 v1 / Archer C20i
Signed-off-by: David Bauer <mail@david-bauer.net>
This drops the shebang from all target files for /lib and
/etc/uci-defaults folders, as these are sourced and the shebang
is useless.
While at it, fix the executable flag on a few of these files.
This does not touch ar71xx, as this target is just used for
backporting now and applying cosmetic changes would just complicate
things.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ramips images now relies on explicit switch setup for proper failsafe
functionality. Remove default cases where it relies on vlan setup in
dts and add switch setup for devices affected.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
The location 0x28 in factory partition is the common one used for
ethernet address on this architecture. Despite, it contains the label
MAC address for the devices at hand.
Consequently, this patch moves 0x28 to the ðernet node in DTS files
(setting the WAN MAC address there) and sets up the lan_mac from 0x22
in 02_network. As a benefit, this allows to use label-mac-device in
DTS instead of ucidef_set_label_macaddr.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Like for the RT-AC54U, this uses a DT trigger for WiFi also at the
RT-AC51U. While at it, rename node and label to wifi2g.
Note that the 5g WiFi LED still isn't supported (see PR #3017 for
further details: https://github.com/openwrt/openwrt/pull/3017 )
Tested-by: Davide Fioravanti <pantanastyle@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The current MAC address assignment for the ASUS RT-AC51U is "wrong",
it actually should be the same as for the RT-AC54U. Fix it.
Thanks to Davide Fioravanti for checking this on his device.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Specification:
- CPU: 580 MHz
- Flash size: 128 MiB NAND
- RAM size: 128 MiB DDR2
- Wireless No1: SoC-integrated: MT7620A 2x2 MIMO 802.11b/g/n (2.4 GHz)
- Wireless No2: On-board chip: MT7612E 2x2 MIMO 802.11a/n/ac (5 GHz)
- Switch: MT7620 built-in 10/100 switch w/ vlan support
- USB: 2.0 x1
Flash instructions:
1. access ssh via https://wiki.openwrt.org/toh/xiaomi/mir3
2. in ssh:
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set uart_en=1
nvram commit
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-kernel1.bin kernel1
mtd write lede-ramips-mt7620-miwifi-r3-squashfs-rootfs0.bin rootfs0
reboot
If you want to revert back to stock fw while on LEDE:
insert usb stick (FAT/FAT32) with stock fw renamed to miwifi.bin
fw_setenv flag_last_success 0
power off the device
hold the reset button and power on the device, keep holding the reset button until yellow led starts blinking.
Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
