Stability of this Ethernet driver has been a long-standing issue, with
many people reporting frequent "transmit queue timeouts" and even
occasional crashes.
Disabling TSO in the driver helps with stability, although it is likely a
workaround and might not fix the issue completely.
There is a slight slowdown in forwarding performance for TCP packets
(75 kpps vs. 80 kpps with comparable CPU utilization), but this is still
enough to forward close to 1 Gbit/s of full-sized packets across multiple
flows.
Master is using a different ethernet driver, so this is not a backport.
Because of this different driver, the upcoming 21.02 release does not seem
to be affected by these stability issues.
Thanks to mrakotiq for the initial patch.
Fixes: FS#2628
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Signed-off-by: Tianling Shen <cnsztl@project-openwrt.eu.org>
The PCI device ID detected by the wifi drivers on devices using a fallback
SPROM is wrong. Currently the chipnum is used for this parameter.
Most SSB based Broadcom wifi chips are 2.4 and 5GHz capable. But on
devices without a physical SPROM, the only one way to detect if the device
suports both bands or only the 5GHz band, is by reading the device ID from
the fallback SPROM.
In some devices, this may lead to a non working wifi on a 5GHz-only card,
or in the best case a working 2.4GHz-only in a dual band wifi card.
The offset for the deviceid in SSB SPROMs is 0x0008, whereas in BCMA is
0x0060. This is true for any SPROM version.
Override the PCI device ID with the one defined at the fallback SPROM, to
detect the correct wifi card model and allow using the 5GHz band if
supported.
The patch has been tested with the following wifi radios:
BCM43222: b43: both 2.4/5GHz working
brcm-wl: both 2.4/5GHz working
BCM43225: b43: 2.4GHz, working
brcmsmac: working
brcm-wl: it lacks support
BCM43217: b43: 2.4GHz, working
brcmsmac: it lacks support
brcm-wl: it lacks support
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Backported from a0e0e621ca
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Specification:
- CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
- DDR3 RAM: 512MB/1GB
- Network:
10/100/1000M Ethernet x 1，
10/100M Ethernet x 1
- WiFi: 802.11b/g/n, with SMA antenna interface
- USB Host: Type-A x2
- MicroSD Slot x 1
- MicroUSB: for OTG and power input
- Debug Serial Port: 3Pin 2.54mm pitch pin-header
- LED:
nanopi:red:status
nanopi:green:wan
nanopi:green:lan
- KEY:
reset
- Power Supply: DC 5V/2A
Installation:
- Write the image to SD Card with dd
- Boot NanoPi from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
x86 uses append-metadata, but only for signing and not for the
metadata itself.
Since recently SUPPORTED_DEVICES was assigned with a global value
and is not empty anymore, append-metadata will now actually put
metadata into x86 images. This breaks sysupgrade on x86.
To fix it for the moment, let's just empty SUPPORTED_DEVICES for
this target again.
In the long term, one should either not add metadata to the images
if it is not desired, and/or remove the unintended fwtool check.
Fixes: f52081bcf9 ("treewide: provide global default for SUPPORTED_DEVICES")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
This drops the shebang from another bunch of files in various /lib
folders, as these are sourced and the shebang is useless.
Fix execute bit in one case, too.
This should cover almost all trivial cases now, i.e. where /lib is
actually used for library files.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Removed restriction of displaying model name for 32 bit tasks only.
Because of this Processor details were not displayed in
"System setting -> Details" in Ubuntu model name display is generic
and can be printed for 64 bit also.
model name : ARMv8 Processor rev X (v8l)
Signed-off-by: Sumit Gupta <sumitg@nvidia.com>
Link: https://lore.kernel.org/lkml/1472461345-28219-1-git-send-email-sumitg@nvidia.com/
Reported-by: AmadeusGhost <amadeus@jmu.edu.cn>
Tested-by: AmadeusGhost <amadeus@jmu.edu.cn>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
(backport from 68692453e2)
This makes it a little easier to figure out which options to choose.
Signed-off-by: Rogan Dawes <rogan@dawes.za.net>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
This hack is not stable and causes some devices against to boot,
users should make oc via their u-boot but not kernel hacks.
This reverts commit 5c6eeab752.
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
This patch will match the clock-latency-ns values in the device tree
for those found inside the OEM device tree and kernel source code and
unlock 896Mhz CPU operating points.
The ASUS MAP-AC2200 suffers from a lower transmit/receive
signal power as compared to the stock firmware.
Upon investigation, it was discovered that stock firmware from
the GPL_MAP-AC2200_3.0.0.4.384.46249-g97d05bb.tar archive.
set the following GPIOs in "release/src/router/rc/init.c".
GPIO 44 and 46 have to be set to output high
GPIO 45 and 47 have to be set to output low
THX @ slh
Fixes: 9ad3967f14 ("ipq40xx: add support for ASUS Lyra")
Signed-off-by: Yushi Nishida <kyro2man@gmx.net>
[slightly rewritten commit, added missing <>)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This fixes tethering with devices using iOS 14. Prior to this patch,
connections to remote endpoints were not possible while data transfers
between the OpenWrt device and the iOS endpoints worked fine.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hauke wrote:
> We want to run some processes in the procd-ujail, this works when we
> use a SquashFS image and an overlay file system, but when we use an
> initramfs it does not work.
> [...]
> When we switch from initramfs to tmpfs, it is working, we added this
> code to target/linux/generic/other-files/init to make [it] work.
Move files to newly mounted tmpfs and then use switch_root to chroot
into new rootfs and free initramfs.
Suggested-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Commit c9c7b4b394 ("kernel: add netfilter-actual-sk patch") has
touched net/ipv6/netfilter/ip6table_mangle.c which in turn has affected
910-unaligned_access_hacks.patch so the patch needs to be refreshed.
Fixes: c9c7b4b394 ("kernel: add netfilter-actual-sk patch")
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Backport of linux kernel commit 46d6c5a to 4.14 kernel.
netfilter: use actual socket sk rather than skb sk when routing harder
Signed-off-by: Aaron Goodman <aaronjg@stanford.edu>
Some devices (especially QCA ones) are already using hardcoded partition
names with colons in it. The OpenMesh A62 for example provides following
mtd relevant information via cmdline:
root=31:11 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(custom),64k(0:KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive) rootfsname=rootfs rootwait
The change to split only on the last colon between mtd-id and partitions
will cause newpart to see following string for the first partition:
KEYS),0x002b0000(kernel),0x00c80000(rootfs),15552k(inactive)
Such a partition list cannot be parsed and thus the device fails to boot.
Avoid this behavior by making sure that the start of the first part-name
("(") will also be the last byte the mtd-id split algorithm is using for
its colon search.
Fixes: 5d01d0560893 ("kernel: Update kernel 4.14 to version 4.14.202")
Fixes: edda06c7b41d ("kernel: Update kernel 4.9 to version 4.9.240")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(backported from commit 223eec7e81)
Both bcm2709 and bcm2710 firmware can run on the same RaspberryPi
models, varying however in 32 and 64 Bit architectures. The model name
alone does not include the architecture information, which becomes
problematic if looking at a overview that only contains the names. By
adding a variant it is possible to tell the architecture.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Define wildcard patterns for filtering in target/linux/generic/config-filter
Preparation for supporting newer kernels
Signed-off-by: Felix Fietkau <nbd@nbd.name>
MikroTik recently changed again the way they store wlan calibration data
on devices. Prior to this change, ERD calibration data for all available
radios was stored within a single identifier node ("tag" in RouterBoot
parlance).
Recent devices have been seen with calibration (and BDF) data stored in
separate identifiers within LZOR packing for each radio: this patch
addresses this by:
1) ensuring that both variants are properly supported,
2) preserving backward compatibility with existing data consumers,
3) allowing for more than 2 calibration blobs to be exposed via sysfs.
Specifically, before this patch, the driver would provide a single sysfs
file named /sys/firmware/mikrotik/hard_config/wlan_data that contained
whatever calibration data found on the device's flash. After this patch,
when executed on a device that uses the old style storage, this behavior
is unchanged, but when executed on a device that uses new style storage
(for either traditional "ERD" packing or "LZOR" packing), the driver
replaces that single file with a folder containing one or more files
each containing the data encoded within individual identifiers.
As far as OpenWRT is concerned, this means that for devices which are
known to exist with both styles of data storage, a suitable hotplug stub
could look like this for e.g. the second radio:
wdata="/sys/firmware/mikrotik/hard_config/wlan_data"
( [ -f "$wdata" ] && caldata_sysfsload_from_file "$wdata" 0x8000 0x2f20 ) || \
( [ -d "$wdata" ] && caldata_sysfsload_from_file "$wdata/data_2" 0x0 0x2f20 )
This patch has been tested with LZOR old and new style packing on ipq4019,
and with old style on ath79.
Tested-by: John Thomson <git@johnthomson.fastmail.com.au>
Tested-by: Шебанов Алексей <admin@ublaze.ru>
Tested-by: Alen Opačić <subixonfire@gmail.com>
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
Tested-by: Robert Marko <robimarko@gmail.com>
CONFIG_EFI_VARS has been disabled in
64bit x86 target in 2018 by the following commit
b0a51dab8c
the same reasons apply to Generic target, so
now it's disabled here too.
Leaving it enabled is also blocking compile as
a new symbol was added
EFI_CUSTOM_SSDT_OVERLAYS
that depends from CONFIG_EFI_VARS
and the build system stops and waits for
user input on what to do about it.
The Legacy and Geode targets never
had any EFI_xxx configs enabled so they
don't have this issue
Signed-off-by: Alberto Bursi <bobafetthotmail@gmail.com>
The original patch from QCA over rode the nf_conntrack_un/register_notifier API, which
will break other modules relying on the API. Reworked the notification APIs to play nice
with others.
The D-Link DIR-645 currently uses an incorrect logic level for its
buttons.
Correct them in order to prevent unintentional activation of failsafe
mode.
Reported-by: Perry Melange <isprotejesvalkata@gmail.com>
Signed-off-by: David Bauer <mail@david-bauer.net>
(cherry picked from commit 929e8f0f55)
The order of function and color in the labels in inverted for the
LAN LEDs. Fix it.
Fixes: 915966d861 ("ath79: Port PowerCloud Systems CAP324 support")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 96023cd4ba)
Hardware Highlights:
- SoC: Qualcomm Atheros AR9531 (650MHz)
- RAM: 128 MB
- Flash: 16 MB SPI NOR
- Ethernet: 10/100: 1x WAN, 4x LAN
- Wireless: QCA9531 2.4GHz (bgn)
- Button: 1x reset button
- LED: SYS, WAN, Wireless, LAN 1~4
Installation:
Configure PC with static IP 192.168.1.x, connect PC with one of RJ45
ports, press the reset button and power up device. Open 192.168.1.1
address in your browser and upload sysupgrade image.
Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
The id parameter in __rb_get_wlan_data() was incorrectly used on the
assumption that id "0" would always be tied to ath9k with RLE encoding
and positive id (in fact, only id "1" was valid) would always be tied to
("external") ath10k with LZO encoding.
Newer hardware revisions of supported devices prove this assumption to
be invalid, with ath9k caldata being now wrapped in MAGIC_ERD and LZO
compressed, so disable this check to allow newer hardware to correctly
decode caldata for ath9k.
Note: this patch assumes that ath9k caldata is never stored with the new
"LZOR" encoding scheme found on some ath10k devices.
Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
(cherry picked from commit 1c6990fe6d)
[keep publishing ath10k caldata in sysfs: it's the way it's done on 18.06]
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Tested-by: Baptiste Jonglez <git@bitsofnetworks.org> [Mikrotik RB941-2nD r3]
reg accesses on integrated ar8229 sometimes fails. As a result, phy read
got incorrect port status and wan link goes down and up mysteriously.
After comparing ar8216 with the old driver, these local_irq_save/restore
calls are the only meaningful differences I could find and it does fix
the issue.
The same changes were added in svn r26856 by Gabor Juhos:
ar71xx: ag71xx: make switch register access atomic
As I can't find the underlying problem either, this hack is broght
back to fix the unstable link issue.
This hack is only suitable for ath79 mdio and may easily break the
driver on other platform. Limit it to ath79-only as a target patch.
Fixes: FS#2216
Fixes: FS#3226
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
(cherry picked from commit 86fdc8abed)
This fixes a regression after a kernel change in 4.14.200 [1] that
led to build failure on oxnas/ox820:
drivers/ata/sata_oxnas.c:2238:13: error: initialization of
'enum ata_completion_errors (*)(struct ata_queued_cmd *)'
from incompatible pointer type
'void (*)(struct ata_queued_cmd *)' [-Werror=incompatible-pointer-types]
.qc_prep = sata_oxnas_qc_prep,
^~~~~~~~~~~~~~~~~~
drivers/ata/sata_oxnas.c:2238:13: note:
(near initialization for 'sata_oxnas_ops.qc_prep')
Our local driver is changed the same way as prototyped in the
kernel patch, i.e. return type is changed and AC_ERR_OK return
value is added.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?id=306a1c5b5683c1d37565e575386139a64bdbec6f
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit f6ca57e4f4)
Kernel config option LEDS_TRIGGER_IDE_DISK was renamed in kernel 4.8 to
CONFIG_LEDS_TRIGGER_DISK in upstream commit eb25cb9956cc ("leds: convert
IDE trigger to common disk trigger").
Removing it as it should be added only on targets which has usage for
this trigger.
Signed-off-by: Thomas Albers <thomas.gameiro@googlemail.com>
[commit description facelift]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
The LED color was missing in 01_leds.
Fixes: 745dee11ac ("ath79: add support for WD My Net Wi-Fi Range
Extender")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This commit add support for the yyets_le router.
Hardware Highlights:
SoC: Qualcomm IPQ4019 717 MHz
RAM: 512M NT5CC256M16ER-EK
Flash: 32M SPI NOR MX25L25635F
WIFI1: 2.4 GHz 2T2R integrated
WIFI2: 5 GHz 2T2R integrated
Ethernet: Qualcomm QCA8075 (4x LAN, 1x WAN)
USB: 1x 3.0
LEDS: power, wlan2g, wlan5g, usb
Button: Reset
Installation:
Upload the firmware on the upgrade page of the stcok, and this will take a few minutes.
This commit also supports the addition of a 128M nand flash version,
just use the P&W R619AC's opboot to overwrite the original uboot.
Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
.dts:226.17-230.4: Warning (spi_bus_reg): /soc/spi@78b6000/spi@1:
SPI bus unit address format error, expected "0"
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
IMAGE_SIZE is widely used in many targets. Declare it in the default template to
clean up redundant code. This also prevents deriving IMAGE_SIZE unintentionally
from the previously defined device.
While at it, remove duplicate KERNEL_SIZE declaration.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The current code acknowledged interrupts *after* polling.
This is the wrong way around, and could cause an interrupt to
be missed.
This is not likely to be fatal as another packet, and so another
interrupt, should come along soon. But maybe it is causing
problems, so let's fix it anyway.
Signed-off-by: NeilBrown <neil@brown.name>
(Note that this matches the upstream driver.)
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This adds a number of options to config/Config-kernel.in so that
packages related to SELinux support can enable the appropriate Linux
kernel support.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
[rebase; add ext4, F2FS, UBIFS, and JFFS2 support; add commit message]
Signed-off-by: W. Michael Petullo <mike@flyn.org>
After years of trying to find the reason for random kernel crashes
while both CPU and SATA are under load it has been found.
Some odd commented-out #defines in kref's single-port driver [1] which
were copied from the vendor driver made me develop a theory:
The IO-mapped memory area for DMA descriptors apparetly got some holes
just before the alignment boundaries.
This feels like an off-by-one bug in the hardware or maybe those fields
are used internally by the SATA controller's firmware.
Whatever the cause is: they cannot be used and trying to use them
results in reading back unexpected stuff and ends up with oopsing
Unable to handle kernel paging request at virtual address d085c004
Work around the issue by reducing the area used for bmdma descriptors.
This reduces SATA performance (iops) quite a bit, but finally makes
things work reliably. Possibly one could optimize this much more by
really just skipping the holes in that memory area -- however, that
seems to be non-trivial with the driver and libata in it's current form
(suggestions are welcome).
The 'proper' way to have good SATA performance would be to make use of
the hardware RAID features (one can use the JBOD mode to access even
just a single disc transparently through the RAID controller integrated
in the SATA host instead of accessing the SATA ports 'raw' as we do
now).
[1]: https://github.com/kref/linux-oxnas/blob/master/drivers/ata/sata_oxnas.c#L25
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The CONFIG_EFI_CUSTOM_SSDT_OVERLAYS option was added in kernel 4.14.188,
set it for the x86/generic target.
This fixes a build problem in the x86/generic target.
Fixes: 148d59c67e ("kernel: update kernel 4.14 to version 4.14.193")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
After those symbols have been removed from generic kernel config,
they were added to the target config during every kernel config
refresh. As that's not desirable, add them back to the generic
config.
Fixes: d1a8217d87 ("kernel: clean-up build-configurable kernel config symbols")
Fixes: cfe235c436 ("kernel: modules: add package kmod-iosched-bfq")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The device uses a rf-kill switch instead of a button. Furthermore the
GPIO is active high.
Signed-off-by: Christoph Krapp <achterin@googlemail.com>
(cherry picked from commit 0af656e978)
WIZnet WizFi630s board name is written slightly different it its OEM
OpenWrt firmware. This causes an incompatibility warning during flashing
with sysupgrade. This patch is adding the vendor board name to the
supported devices list to avoid this warning. For initial flashing you
can use sysupgrade via command line or luci beside of TFTP.
Do not keep the OEM configuration during sysupgrade.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
WIZnet WizFi630S is using only 3 of the phy ports. The unused phy ports
draw unnecessarily power. This is disabling the unused phy ports.
Signed-off-by: Tobias Welz <tw@wiznet.eu>
For the TP-Link 4M devices with tplink-v2-image recipe
(mktplinkfw2.c), there are two different flash layouts based
on the size of the (u)boot partition:
device uboot OEM firmware OpenWrt (incl. config)
tl-wr840n-v5 0x20000 0x3c0000 0x3d0000
tl-wr841n-v14 0x10000 0x3d0000 0x3e0000
In both cases, the 0x10000 config partition is used for the firmware
partition as well due to the limited space available and since it's
recreated by the OEM firmware anyway.
However, the TFTP flashing process will only copy data up to the
size of the initial (OEM) firmware size. Therefore, while we can
use the bigger partition to have additional erase blocks on the
device, we have to limit the image sizes to the TFTP limits.
So far, only one layout definition has been set up in mktplinkfw2.c
for 4M mediatek devices. This adds a second one and assigns them
to the devices so the image sizes are correctly restrained.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
ifconfig is effectively deprecated for quite some time now. Let's
replace the remaining occurrences for our target setup by the
corresponding ip commands now.
Note that this does not touch ar71xx, as it will be dropped anyway,
and changing it would only make backports harder.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The Arduino Yun uses a baud rate of 250000 by default. The serial is
going over the Atmel ATmega and is used to connect to this chip.
Without this patch Linux wants to switch the console to 9600 Baud.
With this patch Linux will use the configured baud rate and not a
default one specified in uart_register_driver().
This has been added for ath79 4.19 and 5.4 in master as part of
fc59b2f79b50 ("ath79: add support for Arduino Yun"), this backports
it separately to 4.14.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Commit 1bfbf2de6d ("ar71xx: serial: core: add support for boot console
with arbitrary baud rates") added support for arbitrary baud rates which
enabled 250000 baud rate for Yun. But the patch was not ported to kernel
4.9, and since then the kernel set its baud rate to 9600. This commit ports
the patch to kernel 4.14, thereby restoring the serial console of Yun.
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Commit 05d73a2a73 enabled GPIO on ethernet LED, but proper LED setup was
not added then. This commit fixes it by reverting the change on the LED.
Fixes: 05d73a2a73 ("ar71xx: Arduino Yun board 'WLAN RST' button support")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Commit bb46b635df changed its partition scheme, but sysupgrade image
validation still uses the old format. This commit fixes it so that
force flag is not needed for sysupgrade.
Fixes: bb46b635df ("ar71xx: move Arduino Yun to generic building code")
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
This symbol is exposed on ARM64 with EFI enabled in the kernel config.
Currently this happens only on ipq807x, but as there might be new ARM64
targets with EFI in the future it is better to add the symbol to the
generic config.
Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
Acked-by: Jo-Philipp Wich <jo@mein.io>
Don't explicitely disable options in target/linux/generic/config-* if
they are already controlled in config/Config-kernel.in.
Add a bunch of new symbols and prepare defaults for using only unified
hierarchy (ie. cgroup2). Update symbol dependencies while at it
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Sometimes when using the DNS-313 memory usage can peak and
with a simple swap partition we can avoid running into the
roof and invoking the OOM killer. Set this partition to
128MB (twice the size of the memory of the DNS-313).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
ZyXEL Keenetic has a USB port. Thus, DWC2 USB controller driver should
be in the default image for this device.
Fixes: a7cbf59e0e ("ramips: add new device ZyXEL Keenetic as kn")
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
[fixed whitespace issue]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
(backported from commit 0a182fcba6)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
In FS#2738 we can see that patch first introduced in
e8ebcff ("ramips: add a explicit reset to dwc2")
breaks USB functionality since 18.06. Thus, this patch should be removed.
Removed:
- 0032-USB-dwc2-add-device_reset.patch
Fixes: FS#2738
Fixes: FS#2964
Signed-off-by: Alexey Dobrovolsky <dobrovolskiy.alexey@gmail.com>
(cherry picked from commit ab841b4393)
Now that check-size uses IMAGE_SIZE by default, we can skip the argument from
image recipes to reduce redundancy.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
[do not touch ar71xx]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
