Package ARM Trusted Firmware host tools separately.
(instead of building tfa-fiptool as part of tfa-layerscape)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
ATF bl2 comes in 4 variants for MT7622 depending on the boot media:
* nor
* snand
* emmc
* sdmmc
Additional binary headers needed for emmc and sdmmc are downloaded as
well and provided along with bl2*.bin and bl31.bin to allow building
images including ATF for MT7622.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The PCI device ID detected by the wifi drivers on devices using a fallback
SPROM is wrong. Currently the chipnum is used for this parameter.
Most SSB based Broadcom wifi chips are 2.4 and 5GHz capable. But on
devices without a physical SPROM, the only one way to detect if the device
suports both bands or only the 5GHz band, is by reading the device ID from
the fallback SPROM.
In some devices, this may lead to a non working wifi on a 5GHz-only card,
or in the best case a working 2.4GHz-only in a dual band wifi card.
The offset for the deviceid in SSB SPROMs is 0x0008, whereas in BCMA is
0x0060. This is true for any SPROM version.
Override the PCI device ID with the one defined at the fallback SPROM, to
detect the correct wifi card model and allow using the 5GHz band if
supported.
The patch has been tested with the following wifi radios:
BCM43222: b43: both 2.4/5GHz working
brcm-wl: both 2.4/5GHz working
BCM43225: b43: 2.4GHz, working
brcmsmac: working
brcm-wl: it lacks support
BCM43217: b43: 2.4GHz, working
brcmsmac: it lacks support
brcm-wl: it lacks support
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
[amend commit description, rework patch to avoid using a new global variable
and keep ssb sprom extraction code as close to ssb/pci.c as possible]
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
New upstream changes extract more SPROM values and fix the antenna gain.
These changes can be found in linux drivers/ssb/pci.c.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Calling netdev_reset_queue() from _stop() functions is causing sporadic kernel
panics on bcm63xx, which happen mainly on BCM6318 and BCM6328.
This reverts to the previous behaviour, which called netdev_reset_queue() from
_open() functions.
Tested on Comtrend AR-5315u (BCM6318).
Fixes: 1d6f422e34 ("bcm63xx: sync ethernet driver with net-next")
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Abort the dhcp-check based on the interface instead of the carrier
state. In cases where the interface is up but the carrier is down,
netifd won't cause a dnsmasq reload, thus dhcp won't become active
on this interface.
Signed-off-by: David Bauer <mail@david-bauer.net>
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.
Build-tested: bcm27xx/bcm2711, ipq806x/R7800,
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Add statistics to ethtool. The statistics can be useful to
debug network issues.
The code is backported from mainline ag71xx.c driver.
Signed-off-by: Leon Leijssen <leon.git@leijssen.info>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
With upstream commit f81f9f0ebac5 ("rockchip: rockpro64: initialize USB in
preboot") CONFIG_USE_PREBOOT was enabled on the RockPro64, which is causing
boot issues when a eMMC is used, as a workaround will temporarily disable
this option.
Signed-off-by: Marty Jones <mj8263788@gmail.com>
[Improve patch description]
Signed-off-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Replace with sed as done elsewhere.
Fixes error with at least btrfs-progs:
Package '@LIBSELINUX@', required by 'mount', not found
Package '@LIBCRYPTSETUP@', required by 'mount', not foun
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Currently it's not possible to boot the device with just initramfs image
without additional effort as the initramfs image doesn't contain device
tree. Fix it by producing FIT based image which could be booted with
following commands:
setenv bootargs earlyprintk console=ttyS0,115200
tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
bootm ${kernel_addr_r}
Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Switch to the normal tarball instead of the codeload generated one. The
latter has the potential to change hashes based on changes in the repo.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Packages that are in-tree only often lack a PKG_VERSION and only use the
PKG_RELEASE to mark changes. Using COMMITCOUNT/AUTORELEASE variables
causes an issue as both variables are empty during the metadata DUMP
phase.
Instead of leaving these variables empty and causing an error message
like below, set the variables to 0 during dumping. On actual building
the variable is evaluated causing in a value above 0.
ERROR: please fix package/utils/px5g-wolfssl/Makefile - \
see logs/package/utils/px5g-wolfssl/dump.txt for details
Makefile:48: *** Package/px5g-wolfssl is missing the VERSION field. Stop.
Reported-by: Daniel Golle <daniel@makrotopia.org>
Reported-by: Stijn Segers <foss@volatilesystems.org>
Reported-by: Stijn Tintel <stijn@linux-ipv6.be>
Signed-off-by: Paul Spooren <mail@aparcar.org>
Upon boot it now prints:
NOTICE: BL1: v2.4(release):OpenWRT v2.4-1 (espressobin-v3-v5-1gb-2cs) (Marvell-devel-18.12.0)
Signed-off-by: Andre Heider <a.heider@gmail.com>
The two required tools fail to identify their version when not compiling
from a git clone, patch that in and pass on the used commit hashes.
Upon boot it now prints "WTMI-devel-18.12.1-5598e150".
Signed-off-by: Andre Heider <a.heider@gmail.com>
The cpufreq issue has been identified and a fix is in the process of beeing
upstreamed [0].
Bump the boards to the default 1000MHz so they can run at that frequency
once the fix is merged. Until then the boards are stuck at 800MHz (just
claiming to run 1000Hz, which is a lie).
[0] https://lore.kernel.org/linux-arm-kernel/20210114124032.12765-1-pali@kernel.org/
Signed-off-by: Andre Heider <a.heider@gmail.com>
The thermal zones kernel documentation is misleading, we cannot use more
than one sensor in a thermal zone node.
Furthermore the drivetemp driver for some reason it only catches one
sensor from the hard drives array (the first available).
In the Buffalo Linkstation LS421DE board there is also a sensor at the
ethernet phy chip that can also be monitored. Very useful to stop the fan
when there are no hard drives in the bays.
(It might be also possible to add the CPU sensor, but it requires kernel
patching for registering the sensor via device tree, using the function:
devm_thermal_zone_of_sensor_register)
Fix the thermal zones to use only one sensor per node and add the ethernet
phy sensor. Also adjust the hdd temperatures to be more conservative for
a mechanical hard drive.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
v5.10 has been released for strace. As such, let's go ahead bring in the
latest version of this package.
See here for the changelog:
https://github.com/strace/strace/releases/tag/v5.10
Signed-off-by: Geordan Neukum <gneukum1@gmail.com>
Pstore (persistent store) can be used to stash debug information (kernel
console, panics, ftrace) across reboots or crashes. If the filesystem is
present, mount it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Specifications:
- SoC: QCA9558
- Flash: 128M NAND
- RAM: 256M
- Ethernet: QCA8337, 1 WAN and 4 LANs
- 2.4GHz wireless: SoC integrated
- 5GHz wireless: QCA9880
- 2 buttons (Reset and WPS)
- 4 GPIO-LEDs
- USB 2.0 port
Flash instructions: (To be done)
Note:
This router has an external watchdog connected to SoC's GPIO 18.
If the watchdog is not fed for about 2 seconds, it will reset the
SoC. Unfortunately, the stock U-boot has a bug that it does not
feed the watchdog when decompressing kernel. If the kernel is
LZMA-compressed, it might take too long before watchdog timeout.
So we have to use gzip instead for faster decompressing speed.
For initramfs image, compression is not used because it is bigger
and will take even more time to decompress.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
