Support new devices LS1046AFRWY and LX2160ARDB in README.
Clean up README, and add missing LS1021ATWR deploy guide.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[adjust set of devices added, update commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The QorIQ LX2160A reference design board provides a comprehensive platform
that enables design and evaluation of the LX2160A processor.
- Enables network intelligence with the next generation Datapath (DPPA2)
which provides differentiated offload and a rich set of IO, including
10GE, 25GE, 40GE, and PCIe Gen4
- Delivers unprecedented efficiency and new virtualized networks
- Supports designs in 5G packet processing, network function
virtualization, storage controller, white box switching, network
interface cards, and mobile edge computing
- Supports all three LX2 family members (16-core LX2160A; 12-core LX2120A;
and 8-core LX2080A)
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[use AUTORELEASE, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The LS1046A Freeway board (FRWY) is a high-performance computing,
evaluation, and development platform that supports the QorIQ
LS1046A architecture processor capable of support more than 32,000
CoreMark performance. The FRWY-LS1046A board supports the QorIQ
LS1046A processor, onboard DDR4 memory, multiple Gigabit Ethernet,
USB3.0 and M2_Type_E interfaces for Wi-Fi.
The FRWY-LS1046A-TP includes the Coral Tensor Flow Processing Unit
that offloads AI/ML inferencing from the CPU to provide significant
boost for AI/ML applications. The FRWY-LS1046A-TP includes one M.2
TPU module and more modules can easily be added including USB
versions of the module to scale the AI/ML performance.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
[rebase, use AUTORELEASE, fix sorting, add dtb to firmware part]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Upcoming devices will not need the migration setup, so let's move
it out of the common definition.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
As kernel size increased it start to fail to load squishfs image,
using lzma-loader fixed it.
wevo_11acnas is almost same device as w2914ns-v2 except ram size,
so I expect same thing would've happen in that device too.
Signed-off-by: Seo Suchan <abnoeh@mail.com>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
The TP-Link EAP235-Wall is a wall-mounted, PoE-powered AC1200 access
point with four gigabit ethernet ports.
When connecting to the device's serial port, it is strongly advised to
use an isolated UART adapter. This prevents linking different power
domains created by the PoE power supply, which may damage your devices.
The device's U-Boot supports saving modified environments with
`saveenv`. However, there is no u-boot-env partition, and saving
modifications will cause the partition table to be overwritten. This is
not an issue for running OpenWrt, but will prevent the vendor FW from
functioning properly.
Device specifications:
* SoC: MT7621DAT
* RAM: 128MiB
* Flash: 16MiB SPI-NOR
* Wireless 2.4GHz (MT7603EN): b/g/n, 2x2
* Wireless 5GHz (MT7613BEN): a/n/ac, 2x2
* Ethernet: 4× GbE
* Back side: ETH0, PoE PD port
* Bottom side: ETH1, ETH2, ETH3
* Single white device LED
* LED button, reset button (available for failsafe)
* PoE pass-through on port ETH3 (enabled with GPIO)
Datasheet of the flash chip specifies a maximum frequency of 33MHz, but
that didn't work. 20MHz gives no errors with reading (flash dump) or
writing (sysupgrade).
Device mac addresses:
Stock firmware uses the same MAC address for ethernet (on device label)
and 2.4GHz wireless. The 5GHz wireless address is incremented by one.
This address is stored in the 'info' ('default-mac') partition at an
offset of 8 bytes.
From OEM ifconfig:
eth a4:2b:b0:...:88
ra0 a4:2b:b0:...:88
rai0 a4:2b:b0:...:89
Flashing instructions:
* Enable SSH in the web interface, and SSH into the target device
* run `cliclientd stopcs`, this should return "success"
* upload the factory image via the web interface
Debricking:
U-boot can be interrupted during boot, serial console is 57600 baud, 8n1
This allows installing a sysupgrade image, or fixing the device in
another way.
* Access serial header from the side of the board, close to ETH3,
pin-out is (1:TX, 2:RX, 3:GND, 4:3.3V), with pin 1 closest to ETH3.
* Interrupt bootloader by holding '4' during boot, which drops the
bootloader into its shell
* Change default 'serverip' and 'ipaddr' variables (optional)
* Download initramfs with `tftpboot`, and boot image with `bootm`
# tftpboot 84000000 openwrt-initramfs.bin
# bootm
Revert to stock:
Using the tplink-safeloader utility from the firmware-utils package,
TP-Link's firmware image can be converted to an OpenWrt-compatible
sysupgrade image:
$ ./staging_dir/host/bin/tplink-safeloader -B EAP235-WALL-V1 \
-z EAP235-WALLv1_XXX_up_signed.bin -o eap235-sysupgrade.bin
This can then be flashed using the OpenWrt sysupgrade interface. The
image will appear to be incompatible and must be force flashed, without
keeping the current configuration.
Known issues:
- DFS support is incomplete (known issue with MT7613)
- MT7613 radio may stop responding when idling, reboot required.
This was an issue with the ddc75ff704 version of mt76, but appears to
have improved/disappeared with bc3963764d.
Error notice example:
[ 7099.554067] mt7615e 0000:02:00.0: Message 73 (seq 1) timeout
Hardware was kindly provided for porting by Stijn Segers.
Tested-by: Stijn Segers <foss@volatilesystems.org>
Signed-off-by: Sander Vanheule <sander@svanheule.net>
Similarly to the Archer C2 v1, the Archer C20 v1 will brick when one
tries to flash an OpenWrt factory image through the TP-Link web UI.
The wiki page contains an explicit warning about this [1].
Disable the factory image altogether since it serves no purpose.
[1] https://openwrt.org/toh/tp-link/tp-link_archer_c20_v1#installation
Signed-off-by: Stijn Segers <foss@volatilesystems.org>
The SPDX license identifier must be in the first line of a file,
unless there is a shebang (then it's the second line).
Fix this for the local files, do not care about the upstream patches.
While at it, update the identifiers where necessary.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The kernel bump to 5.4 has removed the mx25l25635f hack, and the
mx25l25635f compatible is no longer required.
Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Instead of adding those device tree sources using a patch, simply move
them to the newly created dts folder.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
We can now use the power LED for diag in more devices thanks to the latest
patches from the RPi foundation.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Ran update_kernel.sh in a fresh clone without any existing toolchains.
No manual changes needed.
Build system: x86_64
Build-tested: bcm27xx/bcm2711
Signed-off-by: John Audia <graysky@archlinux.us>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
The USB ports if a FRIZZ!Box 7320 do not supply power to connected
devices.
Add the GPIOs enabling USB power as regulator, to enable USB power
supply as soon as the USB driver is loaded.
Fixes FS#3624
Signed-off-by: Mathias Kresin <dev@kresin.me>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Included:
- Hack for support MTWiFi
- HWRNG driver for RK3328 & RK3399
- Fix for hot reboot
- I2C screen support for NanoPi R2S
- Overclocking support for RK3328 and NanoPi4 series
- Ethernet compat node for NanoPi R2S
- Support for NanoPi R4S
Minor adjustments:
- Used r8169 driver for NanoPi R4S by default as r8168 is broken on newer kernel
Refreshed all patches.
Reviewed-by: AmadeusGhost <amadeus@project-openwrt.eu.org>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Remove all upstreamed patches and add the kernel configuration for
version 5.10.
The Rock Pi 4 was split in multiple versions. Add a DTS with the old
name in order to keep compatibility while having kernel 5.4 and 5.10 in
parallel. Switch to the Rock Pi 4A DTS once Kernel 5.4 support is
removed.
Tested-on: Nanoi R2S
Signed-off-by: David Bauer <mail@david-bauer.net>
Reviewed-by: AmadeusGhost <amadeus@project-openwrt.eu.org>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
When recursively deleting partitions, don't acquire the masters
partition lock twice. Otherwise the process endy up in a deadlocked
state.
Signed-off-by: David Bauer <mail@david-bauer.net>
Hardware
--------
MediaTek MT7622
512MB DDR3 RAM
64M SPI-NOR Flash (Winbond W25Q512JV)
MediaTek MT7622 802.11bgn 4T4R WMAC
MediaTek MT7915 802.11ax 4T4R
Marvell AQR1112 100/1000/2500 NBase-T PHY
Holtek HT32F52241 LED controller
Reset Switch
UART
----
CPU UART0 at the pinout next to the Holtek MCU.
Pinout (first pin next to SoC / MCU)
0 3V3
1 RX
2 TX
3 GND
Settings are 115200 8N1.
Opening the case
----------------
Opening the case is not a nice task, as itis glued together. Insert a
flat knife between the front and back casing below the ethernet port.
Open up a gap this way and insert a flat scredriver, remove the knife.
Work your way around the casing by applying force to seperate the front
and back casing. This losens the glue and opens the plastic clips. Be
gentle, as these clips are very cheap and break quickly.
Installation
------------
1. Connect to the booted device at 192.168.1.20 using username/password
"ubnt".
2. Transfer the OpenWrt sysupgrade image to the device using SCP.
3. Check the mtd partition number for bs / kernel0 / kernel1
$ cat /proc/mtd
4. Set the bootselect flag to boot from kernel0
$ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6
5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1
$ dd if=openwrt.bin of=/dev/mtdblock8
$ dd if=openwrt.bin of=/dev/mtdblock9
6. Reboot the device. It should boot into OpenWrt.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED
controller based on the Holtek HT32F52241 MCU.
This driver is initially used by the Ubiquiti UniFi 6 LR, however
judging from FCC pictures the MCU is also found on the U6-Mesh as well
as the U6-Extender.
Signed-off-by: David Bauer <mail@david-bauer.net>
Compile and runtime-tested on mediatek/mt7622
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Kernel has changed the of_get_phy_mode API in commit 0c65b2b90d13
("net: of_get_phy_mode: Change API to solve int/unit warnings").
This is already included in kernel 5.5, so fix the version switch
(though this will not actually matter for the versions we support).
Similar driver adjustments to account for the API change will
probably be necessary to various other local drivers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
This patch has been added to 5.4, but not been copied to 5.10:
7495acb555 ("kernel: backport mtd commit converting partitions doc syntax")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
Reapply changes added to 5.4 but not copied to 5.10:
3da4acaa7b ("kernel: fix busy wait loop in mediatek PPE code")
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.
time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
This applies another patch from 5.4 to 5.10 as well:
de09355f74 ("kernel/hack-5.4: make UDP tunneling user-selectable")
UDP tunneling support isn't user-selectable, but it's required by WireGuard
which is, for the time being, an out-of-tree module. We currently work around
this issue by selecting an unrelated module which depends on UDP tunnelling
(VXLAN). This is inconvenient, as it implies this unrelated module needs to be
built-in when doing a monolithic build.
Fix this inconvenience by making UDP tunneling user-selectable in the kernel
configuration.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
This allows using the last integrated PHY (and so e.g. WAN port on the
ASUS GT-AC5300).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Tianling Shen <cnsztl@project-openwrt.eu.org>
Stability of this Ethernet driver has been a long-standing issue, with
many people reporting frequent "transmit queue timeouts" and even
occasional crashes.
Disabling TSO in the driver helps with stability, although it is likely a
workaround and might not fix the issue completely.
There is a slight slowdown in forwarding performance for TCP packets
(75 kpps vs. 80 kpps with comparable CPU utilization), but this is still
enough to forward close to 1 Gbit/s of full-sized packets across multiple
flows.
Master is using a different ethernet driver, so this is not a backport.
Because of this different driver, the upcoming 21.02 release does not seem
to be affected by these stability issues.
Thanks to mrakotiq for the initial patch.
Fixes: FS#2628
Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
Signed-off-by: Tianling Shen <cnsztl@project-openwrt.eu.org>
This adds quirks support to the "ofpart" parser. It's required to
support fixed partitions that require some extra logic.
Right now only BCM4908 binding is supported (BCM4908 requires detecting
currently used "firmware" partition).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.
time_is_after_jiffies(timeout) will return true until timeout is less
than jiffies, which is the intended behavior here.
Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com>
The Netgear EX6150 has an Access Point/Extender switch. Set it as
an EV_SW. Otherwise when it's set to Access Point, it will trigger
failsafe mode during boot.
Fixes: FS#3590
Signed-off-by: Kurt Roeckx <kurt@roeckx.be>
The factory images need to embed specific IDs to pass verification with
the OEM firmware (including TFTP recovery), so they need to be
per-device variables.
Fixes: ab1584a797 ("ath79: netgear: trim down uImage customisations")
Fixes: 459c8c9ef8 ("ath79: add support for ZyXEL NBG6616")
Reported-by: Marcin Juszkiewicz <marcin-openwrt@juszkiewicz.com.pl>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
[minor commit message adjustments, sort DEVICE_VARS]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
