Specifications:
SoC: MediaTek MT7621
RAM: 256 MB
Flash: 32 MB
WiFi: MediaTek MT7915E
Switch: 1 WAN, 4 LAN (Gigabit)
Ports: 1 USB 3.0
Buttons: Reset, WPS
LEDs: Power, System, Wan, Lan 1-4, WiFi 2.4G, WiFi 5G, WPS, USB
Power: DC 12V 1A tip positive
Installation:
Download and flash the manufacturer's built OpenWRT image available at
http://www.cudytech.com/openwrt_software_download
Install the new OpenWRT image via luci (System -> Backup/Flash firmware)
Be sure to NOT keep settings. The force upgrade may need to be checked
due to differences in router naming conventions.
Recovery:
Loads only signed manufacture firmware due to bootloader RSA verification
serve tftp-recovery image as /recovery.bin on 192.168.1.88/24
connect to any lan ethernet port
power on the device while holding the reset button
wait at least 8 seconds before releasing reset button for image to
download
Signed-off-by: Alessio Prescenzo <alessioprescenzo@gmail.com>
[ensure unique wireless MAC, fix GPIO pingroup]
Signed-off-by: David Bauer <mail@david-bauer.net>
This fixes a bug where frames sent to the switch itself were
flooded to all ports unless the MAC address of the CPU-port
was learned otherwise.
Tested-by: Wenli Looi <wlooi@ucalgary.ca>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Birger Koblitz <git@birger-koblitz.de>
[fix code formatting]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
The ZyXEL GS1900-16 is a 16 port gigabit switch similar to other GS1900 switches.
Specifications
--------------
* Device: ZyXEL GS1900-16
* SoC: Realtek RTL8382M 500 MHz MIPS 4KEc
* Flash: 16 MiB Macronix MX25L12835F
* RAM: 128 MiB DDR2 SDRAM Nanya NT5TU128M8HE
* Ethernet: 16x 10/100/1000 Mbps
* LEDs: 1 PWR LED (green, not configurable)
1 SYS LED (green, configurable)
16 ethernet port link/activity LEDs (green, SoC controlled)
* Buttons: 1 "RESET" button on front panel
* Power 120-240V AC C13
* UART: 1 serial header (J12) with populated standard pin connector on
the right back of the PCB.
Pinout (front to back):
+ Pin 1 - VCC marked with white dot
+ Pin 2 - RX
+ Pin 3 - TX
+ PIn 4 - GND
Serial connection parameters: 115200 8N1.
Installation
------------
OEM upgrade method:
* Log in to OEM management web interface
* Navigate to Maintenance > Firmware
* Select the HTTP radio button
* Select the Active radio button
* Use the browse button to locate the
realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
file amd select open so File Path is update with filename.
* Select the Apply button. Screen will display "Prepare
for firmware upgrade ...".
*Wait until screen shows "Do you really want to reboot?"
then select the OK button
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
U-Boot TFTP method:
* Configure your client with a static 192.168.1.x IP (e.g. 192.168.1.10).
* Set up a TFTP server on your client and make it serve the initramfs image.
* Connect serial, power up the switch, interrupt U-boot by hitting the
space bar, and enable the network:
> rtk network on
* Since the GS1900-16 is a dual-partition device, you want to keep the OEM
firmware on the backup partition for the time being. OpenWrt can only boot
from the first partition anyway (hardcoded in the DTS). To make sure we are
manipulating the first partition, issue the following commands:
> setsys bootpartition 0
> savesys
* Download the image onto the device and boot from it:
> tftpboot 0x84f00000 192.168.1.10:openwrt-realtek-generic-zyxel_gs1900-16-initramfs-kernel.bin
> bootm
* Once OpenWrt has booted, scp the sysupgrade image to /tmp and flash it:
> sysupgrade -n /tmp/openwrt-realtek-generic-zyxel_gs1900-16-squashfs-sysupgrade.bin
it may be necessary to restart the network (/etc/init.d/network restart) on
the running initramfs image.
Signed-off-by: Raylynn Knight <rayknight@me.com>
[removed duplicate patch title, align RAM specification]
Signed-off-by: Sander Vanheule <sander@svanheule.net>
This workaround will allow the MA5671A to function, ignoring the
persistently asserted tx-fault.
Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
(added 5.15 backport)
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
This patch copies over refreshed config and patches from 5.10
with the following changes:
- dropped superfluous tc654/tc655 variant detection patch
(tc654 support will become available upstream starting with
5.17-rc7+).
- dropped xhci msi(x) workaround... as the broken MSI(X)
is now gone.
- dropped dwc2 workaround since the driver was fixed and it
works without it.
Please note: Netgear WNDAP660 & WNDAP620 users:
Due to the kernel's size increase, uboot will likely break
because it is overwrite the kernel during decompression.
To fix this (and debrick affected devices, no reflash
necessary), attach the RJ45-Serial-Console cable and
enter the following in the uboot prompt during bootup:
setenv kernel_addr_r 1100000
saveenv
run bootcmd
to restore the old/previous behavior:
setenv kernel_addr_r 600000
saveenv
run bootcmd
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
With 5.4 out of the picture, remove LINUX_5_10 here. This is
needed for the WNDR4700 as otherwise kmod-usb3 isn't available
for 5.15.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
upstream linux have these watchdogs locked behind X86.
These will not build on other architectures. So move them
to target/linux/x86/modules.mk
drivers/watchdog/Kconfig:
|config F71808E_WDT
| tristate "Fintek F718xx, F818xx Super I/O Watchdog"
| depends on X86
|[...]
|config IT87_WDT
| tristate "IT87 Watchdog Timer"
| depends on X86
|[...]
|config ITCO_WDT
| tristate "Intel TCO Timer/Watchdog"
| depends on (X86 || IA64) && PCI
|[...]
|config W83627HF_WDT
| tristate "Watchdog timer for W83627HF/W83627DHG and compatibles"
| depends on X86
|[...]
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Grommish reported the dreaded build error that happend with 5.4
since the kernel didn't have the cgpio v2 interface. His reason
for the removed 5.4 was that the octeon target had a memory leak
issue, so he had to backport the removed 5.4 kernel for his tests.
Chen Minqiang chimed in and noted that no matter what (i.e.
@TARGET_x86 in depends) didn't prevent the package from being build
on other targets.
From what I can tell, the reason for this was that +nu801 meant
that kmod-meraki-mx100 pulled in an unconditional dependency as
part of to the kernel build.
|scripts/package-metadata.pl mk tmp/.packageinfo
|
|$(curdir)/kernel/linux/compile += $(curdir)/firmware/linux-firmware/compile \
| $(curdir)/firmware/prism54-firmware/compile \
| $(curdir)/kernel/gpio-button-hotplug/compile \
| >>> $(curdir)/system/gpio-cdev/nu801/compile <<<
change this by making the dependency conditional on the
meraki-mx100 module itself. Note that the nu801 enables/sets
the KCONFIG for the cgpio v2 interface itself, since the
userspace program and not the kernel meraki-mx100 relies on it.
Reference: <https://github.com/openwrt/openwrt/commit/eeb8fd4ce7e9>
Reported-by: Grommish <grommish@gmail.com>
Reported-by: Chen Minqiang <ptpt52@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
QEMU+Libvirt can emulate the ib700wdt watchdogs
which due to its I/O-Port mapping makes it x86
specific.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
QEMU can emulate several watchdogs:
aspeed SoC, i6300esb, ib700wdt, imx2, cmsdk-apb and sbsa_gwdt.
Out of these, the ARM SBSA Generic Watchdog (sbsa_gwdt)
makes the most sense for the armvirt' 64 target. Both imx2 and
aspeed are guarded by special vendor specific CONFIG_ in the
upstream kernel.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
the Intel i6300esb is QEMU's default watchdog. And unlike
the real "Intel i6300ESB I/O Controller hub" hardware, the
i6300esb watchdog driver works on non-x86 targets like for
ARM (armvirt 32bit) and potentially virtual PowerPC and MIPS
targets (if there was any).
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Some devices need this to configure the LED configuration. This
way, the correct value for board specific LED configuration can
be determined.
Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
Commit f4fb63d2ab ("ipq40xx: 5.10: move AR40xx to MDIO drivers") moved
the ar40xx driver files to kernel version specific directories to place
them in different subdirectory in kernel tree. But now kernel 5.4 is
gone and there is no reason to keep them separate. Move them back to
common files/ directory.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Also apply commit ab7e53e5cc ("ipq40xx: 5.10: fix ar40xx driver") to
5.15 driver.
The commit fixes the data corruption on TX packets. Packets are
transmitted, but their contents are replaced with zeros. This error is
caused by the lack of guard (50 ms) intervals between calibration phases.
This error is treated by adding mdelay(50) to the calibration function
code. In the original qca-ssda code, these mdelays were existing, but in
the ar41xx.c they are gone.
Fixes: 87318eb179 ("ipq40xx: 5:15: copy config and patch from 5.10")
Signed-off-by: Nick Hainke <vincent@systemli.org>
According wiki https://docs.gl-inet.com/en/2/hardware/mt300n-v2/
GL-MT300N-V2 have I2C interface on GPIO4, GPIO5.
Adding I2C in device tree make possible using I2C on this device.
Signed-off-by: Ptilopsis Leucotis <PtilopsisLeucotis@yandex.com>
Hardware specs:
SoC: Qualcomm IPQ8065 (dual core Cortex-A15)
RAM: 512 MB DDR3
Flash: 256 MB NAND, 32 MB NOR
WiFi: QCA9983 2.4 GHz, QCA9984 5 GHz
Switch: QCA8337
Ethernet: 5x 10/100/1000 Mbit/s
USB: 1x USB 3.0 Type-A
Buttons: WPS, Reset
Power: 12 VDC, 2.5 A
Ethernet ports:
1x WAN: connected to eth2
4x LAN: connected via the switch to eth0 and eth1
(eth0 is disabled in OEM firmware)
MAC addresses (OEM and OpenWrt):
fw_env @ 0x00 d4🆎82:??:??:?a LAN (eth1)
fw_env @ 0x06 d4🆎82:??:??:?b WAN (eth2)
fw_env @ 0x0c d4🆎82:??:??:?c WLAN 2.4 GHz (ath1)
fw_env @ 0x12 d4🆎82:??:??:?d WLAN 5 GHz (ath0)
fw_env @ 0x18 d4🆎82:??:??:?e OEM usage unknown (eth0 in OpenWrt)
OID d4🆎82 is registered to:
ARRIS Group, Inc., 6450 Sequence Drive, San Diego CA 92121, US
More info:
https://openwrt.org/inbox/toh/arris/tr4400_v2
IMPORTANT:
This port requires moving the 'fw_env' partition prior to first boot to
consolidate 70% of the usable space in flash into a contiguous partition.
'fw_env' contains factory-programmed MAC addresses, SSIDs, and passwords.
Its contents must be copied to 'rootfs_1' prior to booting via initramfs.
Note that the stock 'fw_env' partition will be wiped during sysupgrade.
A writable 'stock_fw_env' partition pointing to the old, stock location
is included in the port to help rolling back this change if desired.
Installation:
- Requires serial access and a TFTP server.
- Fully boot stock, press ENTER, type in:
mtd erase /dev/mtd21
dd if=/dev/mtd22 bs=128K count=1 | mtd write - /dev/mtd21
umount /config && ubidetach -m 23 && mtd erase /dev/mtd23
- Reboot and interrupt U-Boot by pressing a key, type in:
set mtdids 'nand0=nand0'
set mtdparts 'mtdparts=nand0:155M@0x6500000(mtd_ubi)'
set bootcmd 'ubi part mtd_ubi && ubi read 0x44000000 kernel && bootm'
env save
- Setup TFTP server serving initramfs image as 'recovery.bin', type in:
set ipaddr 192.168.1.1
set serverip 192.168.1.2
tftpboot recovery.bin && bootm
- Use sysupgrade to install squashfs image.
This port is based on work done by AmadeusGhost <amadeus@jmu.edu.cn>.
Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com>
[add 5.15 changes for 0069-arm-boot-add-dts-files.patch]
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
Add NVRAM quirks script for the bcm53xx target. Split NVRAM quirks for the
bcm47xx and bcm53xx targets. Move clear partialboot NVRAM quirk for Linksys
EA9500 here. Add set wireless LED behaviour quirk for Asus RT-AC88U.
Use boot() instead of start() as nvram commands are meant to be executed
only once, at boot.
Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com>
Remove restrictions on source and destination addresses, which aren't
specified on RFC8415, and for some reason in openwrt are configured
to allow both link-local and ULA addresses.
As cleared out in issue #5066 there are some ISPs that use Gloabal
Unicast addresses, so fix this rule to allow them.
Fixes: #5066
Signed-off-by: Tiago Gaspar <tiagogaspar8@gmail.com>
[rebase onto firewall3, clarify subject, bump PKG_RELEASE]
Signed-off-by: Jo-Philipp Wich <jo@mein.io>
Stop the connection when the control daemon is terminated. The code is
a modified version of the termination routine in version 4.23.1 of the
daemon (which doesn't support VR9 modems anymore).
This could also be implemented by calling the acos and acs commands via
dsl_cpe_pipe.sh in the init script. However, doing it in the daemon
itself has the advantage of also working if it is terminated in another
way (for example during sysupgrade).
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
The driver maintains elapsed times by repeatedly accumulating the time
since the previous update in a loop. For the elapsed showtime time, the
time difference is truncated to seconds before adding it, leading to a
sizable error over time.
Move the truncation to before calculation of the time difference in
order to remove this error. Also maintain the total elapsed time in the
same way in full seconds, to prevent the unsigned 32-bit counter from
wrapping around after about 50 days.
Testing on a VR9 device shows that the reported line uptime now matches
the actual elapsed wall time. The ADSL variant is only compile-tested,
but it should also work as the relevant code is identical.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Right now, both ltq-adsl-mei and ltq-vdsl-mei are always built, even
when they aren't necessary for the selected variant. This can cause the
build to fail, for example ltq-vdsl-mei doesn't build successfully here
on xway target due to the vectoring callback.
Make these dependencies conditional on the specific package variants,
so they are only built when actually needed.
Signed-off-by: Jan Hoffmann <jan@3e8.eu>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
