This patch adds supports for the GL-B2200 router.
Specifications:
- SOC: Qualcomm IPQ4019 ARM Quad-Core
- RAM: 512 MiB
- Flash: 16 MiB NOR - SPI0
- EMMC: 8GB EMMC
- ETH: Qualcomm QCA8075
- WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2
- WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2
- WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2
- INPUT: Reset, WPS
- LED: Power, Internet
- UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1
- UART2: On board with BLE module
- SPI1: On board socket for Zigbee module
Update firmware instructions:
Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at
https://docs.gl-inet.com/en/3/troubleshooting/debrick/).
Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware.
Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first.
What's working:
- WiFi 2G, 5G
- WPA2/WPA3
Not tested:
- Bluetooth LE/Zigbee
Credits goes to the original authors of this patch.
V1->V2:
- updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake)
- add uboot-envtools support
V2->V3:
- Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface
V3->V4:
- wire up sysupgrade
Signed-off-by: Li Zhang <li.zhang@gl-inet.com>
[fix tab and trailing space, document what's working and what's not]
Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro>
[rebase on top of master, address remaining comments]
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
[remove redundant check in platform.sh]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The configs/omap3_overo_defconfig file was removed from upstream U-Boot
in commit ed3294d6d1f9 ("arm: Remove overo board"). Remove it in OpenWrt
too. If someone needs this please add it also to upstream U-Boot.
This fixes the compile of the omap target.
Fixes: ffb807ec90 ("omap: update u-boot to 2021.07")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Follow up to commit 565b62cca2. Managed to
hit the very same issue again while playing with the NOR SPL builds.
Signed-off-by: Mathias Kresin <dev@kresin.me>
With cryptocpp in place we can now update past the point of dropping
the old tbb_linux binary and build it instead.
Hauke confirmed that this also allows this firmware to be built on
aarch64.
97f01f5 Wtpdownloader: Properly retrieve current tty options
a33ff86 Wtpdownloader: Set CREAD tty cflag
af461d2 Wtpdownloader: Fix stuck during opening UART tty device
38c2135 Makefile: Print error when specified CLOCKSPRESET is not valid
f014428 TBB: Remove out-of-dated x86-64 ELF binary tbb_linux
1b6cb50 TBB: Fix compilation with Crypto++ 5.6.5
d9fb291 TBB: Fix memory corruptions by calling correct delete[] operator
d575885 TBB: Fix initializing CCTIM object
b9e1c4e Wtpdownloader: Fix makefile
8f61591 Wtpdownloader: Fix building with gcc 11
eabea5f TBB: Fix building with gcc 11
Signed-off-by: Andre Heider <a.heider@gmail.com>
Based on the Build Instructions for Trusted-Firmware-A [1],
there is a required cryptopp [2].
In the past, it used 'tbb_linux' image tool binary, which seems to
be buggy, deprecated and removed from A3700-utils-marvell and it should
not be used anymore. That's why I removed 001-imagetool.patch, which is
no longer necessary.
[1] https://trustedfirmware-a.readthedocs.io/en/v2.5/plat/marvell/armada/build.html
[2] https://cryptopp.com/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
without this patch a3700-utils/tim/ddr/ddr_tool.verstr contains the OpenWrt commit ID.
this patch fix the mv_ddr version commit ID by using the global variable MV_DDR_COMMIT_ID.
Upon boot it now prints "mv_ddr-devel-g02e23dbc-d DDR4 16b 1GB 1CS".
Cc: Andre Heider <a.heider@gmail.com>
Signed-off-by: Kerma Gérald <gandalf@gk2.net>
On lantiq a lot of stuff expects to be loaded to and executed at
0x80002000, including our own second stage bootloader.
For all build u-boots, the initial stack pointer is at 0x80008000. After
loading data to 0x80002000, every further stack operation corrupts the
loaded code.
Set the initial stack pointer to 0x80002000, to not overwrite code
loaded in memory. A stack of 0x2000 bytes has been proven as enough in
all done tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
On danube we only have 0x6800 bytes of usable SRAM. Everything behind
can't be written to and a SPL u-boot locks up during boot.
Since it's a hard to debug issue and took me more than two years to fix
it, I consider it worth to include fix albeit SPL u-boots are not build
in OpenWrt.
I faced the issue while trying to shrink the u-boot to 64K since some
boards only have an u-boot partition of that size from the days
ifx-uboot was used.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
With gcc10 the variables are placed more tightly to each other, which
uncovers a long existing bug in the lantiq DMA code. It can be observed
when using tftpboot with the filename parameter, which gets reset during
the tftpboot execution.
NetRxPackets[] points to cache line size aligned addresses. In
ltq_eth_rx_packet_align() the address NetRxPackets[] points to is
increased by LTQ_ETH_IP_ALIGN and the resulting not cache aligned
address is used further on. While doing so, the length/size is never
updated.
The "not cache aligned address" + len/size for a cache aligned address
is passed to invalidate_dcache_range(). Hence, invalidate_dcache_range()
invalidates the next 32 bit as well, which flashes the BootFile variable
as well.
variable BootFile is at address: 0x83ffe12c
NetRxPackets[] points to 0x83ffdb20 (len is 0x600)
data points to: 0x83ffdb22 (len is 0x600)
ltq_dma_dcache_inv: 0x83ffdb22 (for len 0x600)
invalidate_dcache_range: 0x83ffdb20 to 0x83ffe120 (size: 32)
invalidate_dcache_range: 0x83ffdb20 to 0x83ffdb40 (Bootfile: a.bin)
...
invalidate_dcache_range: 0x83ffe100 to 0x83ffe120 (Bootfile: a.bin)
invalidate_dcache_range: 0x83ffe120 to 0x83ffe140 (Bootfile: )
In ltq_dma_tx_map() and ltq_dma_rx_map() the start address passed to
ltq_dma_dcache_wb_inv() is incorrect. By considering the offset, the
start address passed to flush_dcache_range() is always aligned to 32, 64
or 128 bytes dependent on configured DMA burst size.
Fixes: FS#4113
Signed-off-by: Mathias Kresin <dev@kresin.me>
At least since gcc 7.3.0 (OpenWrt 18.06) lwr/lwl are used in the
assembly of LzmaProps_Decode. While the decission made by the compiler
looks perfect fine, it triggers some obscure hang on lantiq danube-s
v1.5 with MX29LV640EB NOR flash chips.
Only if the offset 1 is used, the hang can be observed. Using any other
offset works fine:
lwl s0,0(a1) - s0 == 0x6d000080
lwl s0,1(a1) - hangs
lwl s0,2(a1) - s0 == 0x0080xxxx
lwl s0,3(a1) - s0 == 0x80xxxxxx
It isn't clear whether it is a limitation of the flash chip, the EBU or
something else.
Force 8bit reads to prevent gcc optimizing the read with lwr/lwl
instructions.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Subtarget-specific files under 'uboot-envtools' package are supported
since 6f3a05ebb0 ("uboot-envtools: support uci-default config also per
subtargets").
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
Dongwon T&I DW02-412H is a 2.4/5GHz band 11ac (WiFi-5) router, based on
Qualcomm Atheros QCA9557.
Specifications
--------------
- SoC: Qualcomm Atheros QCA9557-AT4A
- RAM: DDR2 128MB
- Flash: SPI NOR 2MB (Winbond W25Q16DVSSIG / ESMT F25L16PA(2S)) +
NAND 64/128MB
- WiFi:
- 2.4GHz: QCA9557 WMAC
- 5GHz: QCA9882-BR4A
- Ethernet: 5x 10/100/1000Mbps
- Switch: QCA8337N-AL3C
- USB: 1x USB 2.0
- UART:
- JP2: 3.3V, TX, RX, GND (3.3V is the square pad) / 115200 8N1
Installation
--------------
1. Connect a serial interface to UART header and
interrupt the autostart of kernel.
2. Transfer the factory image via TFTP and write it to the NAND flash.
3. Update U-Boot environment variable.
> tftpboot 0x81000000 <your image>-factory.img
> nand erase 0x1000000
> nand write 0x81000000 0x1000000 ${filesize}
> setenv bootpart 2
> saveenv
Revert to stock firmware
--------------
1. Revert to stock U-Boot environment variable.
> setenv bootpart 1
> saveenv
MAC addresses as verified by OEM firmware
--------------
WAN: *:XX (label)
LAN: *:XX + 1
2.4G: *:XX + 3
5G: *:XX + 4
The label MAC address was found in art 0x0.
Credits
--------------
Credit goes to the @manatails who first developed how to port OpenWRT
to this device and had a significant impact on this patch.
And thanks to @adschm and @mans0n for guiding me to revise the code
in many ways.
Signed-off-by: Jihoon Han <rapid_renard@renard.ga>
Reviewed-by: Sungbo Eo <mans0n@gorani.run>
Tested-by: Sungbo Eo <mans0n@gorani.run>
This commit adds support for Xiaomi MiWiFi 3C device.
Xiaomi MiWifi 3C has almost the same system architecture
as the Xiaomi Mi WiFi Nano, which is already officially
supported by OpenWrt.
The differences are:
- Numbers of antennas (4 instead of 2). The antenna management
is done via the µC. There is no configuration needed in the
software code.
- LAN port assignments are different. LAN1 and WAN are
interchanged.
OpenWrt Wiki: https://openwrt.org/toh/xiaomi/mir3c
OpenWrt developers forum page:
https://forum.openwrt.org/t/support-for-xiaomi-mi-3c
Specifications:
- CPU: MediaTek MT7628AN (575MHz)
- Flash: 16MB
- RAM: 64MB DDR2
- 2.4 GHz: IEEE 802.11b/g/n with Integrated LNA and PA
- Antennas: 4x external single band antennas
- WAN: 1x 10/100M
- LAN: 2x 10/100M
- LED: 1x amber/blue/red. Programmable
- Button: Reset
MAC addresses as verified by OEM firmware:
use address source
LAN *:92 factory 0x28
WAN *:92 factory 0x28
2g *:93 factory 0x4
OEM firmware uses VLAN's to create the network interface for WAN and LAN.
Bootloader info:
The stock bootloader uses a "Dual ROM Partition System".
OS1 is a deep copy of OS2.
The bootloader start OS2 by default.
To force start OS1 it is needed to set "flag_try_sys2_failed=1".
How to install:
1- Use OpenWRTInvasion to gain telnet, ssh and ftp access.
https://github.com/acecilia/OpenWRTInvasion
(IP: 192.168.31.1 - Username: root - Password: root)
2- Connect to router using telnet or ssh.
3- Backup all partitions. Use command "dd if=/dev/mtd0 of=/tmp/mtd0".
Copy /tmp/mtd0 to computer using ftp.
4- Copy openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin
to /tmp in router using ftp.
5- Enable UART access and change start image for OS1.
```
nvram set uart_en=1
nvram set flag_last_success=1
nvram set boot_wait=on
nvram set flag_try_sys2_failed=1
nvram commit
```
6- Installing Openwrt on OS1 and free OS2.
```
mtd erase OS1
mtd erase OS2
mtd -r write /tmp/openwrt-ramips-mt76x8-xiaomi_miwifi-3c-squashfs-sysupgrade.bin OS1
```
Limitations: For the first install the image size needs to be less
than 7733248 bits.
Thanks for all community and especially for this device:
minax007, earth08, S.Farid
Signed-off-by: Eduardo Santos <edu.2000.kill@gmail.com>
[wrap lines, remove whitespace errors, add mediatek,mtd-eeprom to
&wmac, convert to nvmem]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Add support for SAM9X60-EK board.
Hardware:
- SoC: SAM9X60
- RAM: Winbond W972GG6KB-25 (2Gbit DDR2)
- NAND Flash: Micron MT29F4G08ABAEA
- QSPI Flash: Microchip SST26VF064B
- EEPROM: Microchip 24AA02E48
- SDMMC: One standard 4-bit SD card interface
- USB: two stacked Type-A connectors with power switches, one micro-B
USB device
- CAN: 2 interfaces (Microchip MCP2542)
- Ethernet: one 10/100Mbps
- WiFi/BT: one optional WiFi/Bluetooth interface
- Audio: one ClassD port
- Display: one 24-bit LCD interface
- Camera: one 12-bit image sensor interface
- IO: one IO expander (Microchip MCP23008)
- Debug ports: one J-Link-OB + CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: 4 push button switches
- Expansion: one PIO connector, one mikrobus connector
- Power management: two power regulators, two power consumption measurement
devices
Flashing:
- follow the procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sam9x60EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D27 WLSOM1-EK board.
Hardware:
- SIP: SAMA5D27C-LD2G-CU including SAMA5D27 MPU and 2Gbit LPDDR2-SDRAM
- MMC: one standard SD card interface
- Flash: 64 Mb serial quad I/O flash memory (SST26VF064BEUIT-104I/MF)
with embedded EUI-48 and EUI-64 MAC addresses
- USB: one USB device, one USB host one HSIC interface
- Ethernet: 1x10/100Mbps port
- WiFi/BT: IEEE 802.11 b/g/n Wi-Fi plus Bluetooth (Wi-Fi/BT) module
(ATWILC3000-MR110UA)
- Crypto: one ATECC608B-TNGTLS secure element
- Video: one LCD RGB 18-bit interface, one ISC 12-bit camera interface
- Debug port: one JTAG interface, one UART interface, one WILC UART
interface
- Leds: one RGB LED
- Buttons: start, reset, wakeup, user buttons
- Expansion: one tamper connector, one mikrobus interface, 2 XPRO PTC
connector
- Power managament: PMIC (MCP16502)
Flashing:
- follow procedure at [1]
[1] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d27WLSom1EKMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Add support for SAMA5D2 ICP board.
Hardware:
- SoC: SAMA5D27
- RAM: 512 MB DDR3L
- MMC: One stanard SD card interface
- USB: One USB host switch 4 ports with power switch,
One USB device type Micro-AB
- CAN: 2 interfaces
- Ethernet: One Gigabit Ethernet PHY through HSIC,
One ETH switchport,
One EtherCAT interface
- WiFi/BT: Footprint for IEEE 802.11 b/g/n Wi-Fi plus
Bluetooth module (Wi-Fi/BT), suitable for
Microchip WILC3000-MR110CA or WILC3000-MR110UA
- Debug port: One J-Link-OB/J-Link-CDC, one JTAG interface
- Leds: one RGB LED
- Buttons: reset, wakeup, 2 user buttons
- Expansion: one PIOBU/PIO connector, 3 mikrobus sockets
- Power mangament: PMIC (MCP16502), one power consumption device
(PAC1934)
Not working in Linux:
- EtherCAT interface: there is no Linux support integrated
- PAC1934: driver available at [1] but not integrated in Linux
Flashing:
- follow the procedure at [2]
[1] https://ww1.microchip.com/downloads/en/DeviceDoc/pac193x_linux_driver.zip
[2] https://www.linux4sam.org/bin/view/Linux4SAM/Sama5d2IcpMainPage#Create_a_SD_card_with_the_demo
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Host libraries are only build static, so let's pass --static to
pkg-config globally and remove the then unnecessary patches doing
exactly that individually.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Using Host/Exports doesn't work as intended, explicitly add the
required vars so that u-boot finds the required libraries when building
its tools.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Kernel has added the different variants of the Rock Pi 4 in commit
b5edb0467370 ("arm64: dts: rockchip: Mark rock-pi-4 as rock-pi-4a
dts"). The former Rock Pi 4 is now Rock Pi 4A.
For compatibility with kernel 5.4, this rename has been held back
so far. Having switched to kernel 5.10 now, we can finally apply
it in our tree as well.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
U-Boot 2021.10 has been released.
Rebase mediatek patches on top of new release and remove some patches
which have been merged upstream.
Tested on Bananapi BPi-R2 (mt7623), Bananapi BPi-R64 (mt7622) and
Linksys E8450 (mt7622).
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Nobody ever updates PKG_RELEASE when changing devices or setup in
the various uboot-* packages. Use $(AUTORELEASE) so we still have
proper versioning there.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Globalscale MOCHAbin is a Armada 7040 based development board.
Specifications:
* Armada 7040 Quad core ARMv8 Cortex A-72 @ 1.4GHz
* 2 / 4 / 8 GB of DDR4 DRAM
* 16 GB eMMC
* 4MB SPI-NOR (Bootloader)
* 1x M.2-2280 B-key socket (for SSD expansion, SATA3 only)
* 1x M.2-2250 B-key socket (for modems, USB2.0 and I2C only)
* 1x Mini-PCIe 3.0 (x1, USB2.0 and I2C)
* 1x SATA 7+15 socket (SATA3)
* 1x 16-pin (2×8) MikroBus Connector
* 1x SIM card slot (Connected to the mini-PCIe and both M.2 slots)
* 2x USB3.0 Type-A ports via SMSC USB5434B hub
* Cortex 2x5 JTAG
* microUSB port for UART (PL2303GL/PL2303SA onboard)
* 1x 10G SFP+
* 1x 1G SFP (Connected to 88E1512 PHY)
* 1x 1G RJ45 with PoE PD (Connected to 88E1512 PHY)
* 4x 1G RJ45 ports via Topaz 88E6141 switch
* RTC with battery holder (SoC provided, requires CR2032 battery)
* 1x 12V DC IN
* 1x Power switch
* 1x 12V fan header (3-pin, power only)
* 1x mini-PCIe LED header (2x0.1" pins)
* 1x M.2-2280 LED header (2x0.1" pins)
* 6x Bootstrap jumpers
* 1x Power LED (Green)
* 3x Tri-color RGB LEDs (Controllable)
* 1x Microchip ATECC608B secure element
Note that 1G SFP and 1G WAN cannot be used at the same time as they are in
parallel connected to the same PHY.
Installation:
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a72_musl/linux-mvebu_cortexa72/image-armada-7040-mochabin.dtb bin/targets/mvebu/cortexa72/
$ in.tftpd -L -s bin/targets/mvebu/cortexa72/
Connect to the device UART via microUSB port and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Set the ethernet device (Example for the 1G WAN):
$ setenv ethact mvpp2-2
Ping server to confirm network is working:
$ ping $serverip
Using mvpp2-2 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa72-globalscale_mochabin-initramfs-kernel.bin
$ tftpboot $fdt_addr_r image-armada-7040-mochabin.dtb
Boot the image:
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa72-globalscale_mochabin-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Hit any key to stop the autoboot.
Reset U-boot env and set the bootcmd:
$ env default -a
$ setenv bootcmd 'load mmc 0 ${loadaddr} boot.scr && source ${loadaddr}'
Optionally I would advise to edit the console env variable to remove earlycon as that
causes the kernel to never use the driver for the serial console.
Earlycon should be used only for debugging before the kernel can configure the console
and will otherwise cause various issues with the console.
$ setenv console 'console=ttyS0,115200'
Save and reset
$ saveenv
$ reset
OpenWrt should boot from eMMC now.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Fix BPi-R2 GPIO LEDs to indicate boot into production or recovery
firmware in DTS and define them in default environment.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Fixes compilation with GCC11.
Kept PKG_VERSION as there's some bug that chops off the 12 at the end.
Refreshed other patch.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
This adds the hash also for the aarch64 toolchain in addition to the
x86_64 toolchain. This gets the build on a Linux aarch64 host one step
further.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
