This board is also as known as Bananapi BPi-M7.
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
8/16/32GB LPDDR4/LPDDR4x RAM
2x 2500 Base-T (PCIe, rtl8125b)
AP6275P Wi-Fi 6 / Bluetooth 5
2 LEDs (RED / GREEN)
16GB/32GB/64GB/128GB eMMC on-board
Micro-SD Slot
HDMI Port
USB 2.0 Port
USB 3.0 Port
USB Type-C 3.0 Port
M.2 M-Key
40-Pin Header
USB PD 2.0 9/12/15V Power
Installation
------------
Uncompress the ImmortalWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware spec:
- Rockchip RK3568 Quad-core ARM Cortex-A55 CPU 2GHz
- GPU Mali-G52 1-Core-2EE OpenGL ES3.2 Vu1kn 1.1 OpenCL 2.0
- Memory2G DDR3 SDRAM (option 4G)
- Storage Onboard 16GB eMMC Flash, Micro SD-Card slot, SATA 3.0 Port,SPI flash
- Network 5 x 10/100/1000 Mbit/s Ethernet MT7531
- Display 1 HDMI port, 2 DSI interface(1 DSI can change to LVDS by software)
- Camera 1 CSI camera interface
- Audio Output HDMI & I2S & Speaker & Headphone
- USB port USB 3.0 PORT (x2), micro USB OTG (x1)
- PCIE 1 mini pcie interface & 1 M.2 key-e interface
- Remote IR Receiver (x1)
- GPIO 40 Pin Header : GPIO (x28) and Power (+5V, +3.3V and GND).
- Switches Reset button, Power button, U-boot button
- LED Power Status
- Power Source 12 volt 2A via DC Power
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
Boot from the SD card
1-hold down the MaskRom button
2-Connect DC power
3-Wait 5 seconds, release the button.
eMMC Installation:
1-Uncompress the OpenWrt sysupgrade image
2-fash to eMMC
dd if=openwrt-rockchip-armv8-sinovoip_bpi-r2-pro-squashfs-sysupgrade.img of=/dev/mmcblk1
sync
3-remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Radxa E25 is a network application carrier board for the Radxa CM3
Industrial (CM3I) SoM, which is based on the Rockchip RK3568 SoC.
It has the following features:
- MicroSD card socket, on board eMMC flash
- 2x 2.5GbE Realtek RTL8125B Ethernet transceiver
- 1x USB Type-C port (Power and Serial console)
- 1x USB 3.0 OTG port
- mini PCIe socket (USB or PCIe)
- ngff PCIe socket (USB or SATA)
- 1x User LED and 16x RGB LEDs
- 26-pin expansion header
Installation:
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
RGB LED
1/2/4/8GB LPDDR4 RAM
2x 2500 Base-T
2/16/32/64/128GB eMMC on-board
M.2 Slot
miniPCIe Slot
Micro-SD Slot
USB 3.0 Port
Type-C PD Power
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3568 ARM64 (4 cores)
2GB or 4GB LPDDR4 RAM
2x 1000 Base-T
QCA1023 Wi-Fi 5 / Bluetooth
16GB or 64GB eMMC on-board
2x M.2 Slot (B+E Key)
Micro-SD Slot
HDMI Port
USB 3.0 Port
7000 mAh Battery
Type-C Power
Note
----
The sdio card QCA1023 is not supported for now due to broken
ath10k-sdio driver.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Now we support parsing the color and function properties.
Ref: e814acc599 ("base-files: support parse DT LED color and function")
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Hardware
--------
RockChip RK3566 ARM64 (4 cores)
- up to 8GB LPDDR4X
- 1x HDMI,
- 2x MIPI DSI
- 2x MIPI CSI2
- 1x eDP
- 1x PCIe card
- 2x SATA
- 2x USB 2.0 Host
- 1x USB 3.0
- 1x USB 2.0 OTG
- 10/100/1000 Base-T
- microSD slot
- 40-pin GPIO expansion header
- 12V DC
Radxa CM3 needs to mount on top of this IO board in order to create
complete Radxa CM3 IO board platform.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: Marius Durbaca <mariusd84@gmail.com>
FriendlyElec renamed the NanoPi R4S board with EEPROM (mac address)
to "enterprise" edition, and it was added as a "new" board in upstream
kernel.
This patch switched to use that upstreamed dts and removed local
EEPROM patch.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The NanoPi R2C Plus is a small variant of NanoPi R2C with a on-board
eMMC flash (8G) included.
Installation
------------
Uncompress the OpenWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
XHCI bus numbers are assigned dynamically, it may varies among boards,
match the device irq name with regexp, drop the hardcoded name.
Signed-off-by: Furong Xu <xfr@outlook.com>
Hardware
--------
RockChip RK3588 ARM64 (8 cores)
4/8/16GB LPDDR4X RAM
2x 2500 Base-T (PCIe, rtl8125b)
2 LEDs (POWER / WAN)
32/64/256GB eMMC on-board
Micro-SD Slot
USB 2.0 Port
Headphone
USB 3.0
USB PD 2.0
M.2 M-Key
M.2 E-Key
DC Jack 12V
Installation
------------
Uncompress the ImmortalWrt sysupgrade and write it to a micro SD card or
internal eMMC using dd.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Without it the WAN port won't be initialized properly.
Fixes: 8f578c15b3 ("rockchip: add NanoPi R2C support")
Reviewed-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and otherwise
identical to OrangePi R1 Plus.
Tested-by: Volkan Yetik <no3iverson@gmail.com>
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
Note: booting from SPI is currently unsupported, you have to install
the image on a SD card.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
The NanoPi R2C is a minor variant of NanoPi R2S with the on-board NIC
chip changed from rtl8211e to yt8521s, and otherwise identical to R2S.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Ensure the MAC address for all NanoPi R1 boards is assigned uniquely for
each board.
The vendor ships the device in two variants; one with and one without
eMMC; but both without static mac-addresses.
In order to assign both board types unique MAC addresses, fall back on
the same method used for the NanoPi R2S and R4S in case the EEPROM
chip is not present by generating the board MAC from the SD card CID.
[0] https://wiki.friendlyelec.com/wiki/index.php/NanoPi_R1#Hardware_Spec
Similar too and based on:
commit b5675f500d ("rockchip: ensure NanoPi R4S has unique MAC address")
Co-authored-by: David Bauer <mail@david-bauer.net>
Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me>
