Ran update_kernel.sh in a fresh clone without any existing toolchains.
Removed upstreamed:
mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch
Build system : x86_64
Build-tested : ipq806x/R7800
Run-tested : ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
CPU: Allwinner V40 quad-core Cortex A7 @ 1.2GHz
Memory: 1GB DDR3
Storage: SDcard, native SATA
Network: 10/100/1000M ethernet, Ampak AP6212 wifi + BT
USB: 4x USB 2.0
Installation:
Use the standard sunxi installation to an SD-card.
While the board is very similar to the M2 Ultra board
(the V40 is the automotive version of the R40), as both
the u-boot and kernel supports them separately, and some
pins are different, let's add a separate device spec.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
LPAE should be disabled as the Cortex-A8 cores don't support it,
and the kernel will crash on boot if it's enabled.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The Pine64(+) and the SoPine64 baseboard has an optional BT+WiFi
module, carrying an RTL8723BS. The wifi part is connected via
SDIO, the BT part is connected via UART. The BT part requires
additional code changes in the drivers so we'll skip that until 5.10.
Aside from a DTS patch to enable the wifi module, add the required
packages into the device definitions.
[ 8.996970] RTL8723BS: module init start
[ 9.000922] RTL8723BS: rtl8723bs v4.3.5.5_12290.20140916_BTCOEX20140507-4E40
[ 9.007965] RTL8723BS: rtl8723bs BT-Coex version = BTCOEX20140507-4E40
[ 9.014785] pnetdev = 000000009bdd5000
[ 9.047780] RTL8723BS: rtw_ndev_init(wlan0)
[ 9.053349] RTL8723BS: module init ret =0
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The Pine64(+) and the SoPine64 baseboard has two USB ports. One of
these (the lower) is connected directly to a USB host, the other
one's (upper) PHY is shared with the separate OTG controller. In
order to get it working, MUSB support needs to be enabled.
As there are other targets which compile MUSB support into the kernel
and not package it into modules, the same is done here.
[ 1.348760] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.04
[ 1.357029] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.364250] usb usb5: Product: MUSB HDRC host driver
[ 1.369219] usb usb5: Manufacturer: Linux 5.4.99 musb-hcd
[ 1.374617] usb usb5: SerialNumber: musb-hdrc.1.auto
[ 1.379891] hub 5-0:1.0: USB hub found
[ 1.383677] hub 5-0:1.0: 1 port detected
[...]
[ 697.299440] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 697.461855] usb 1-1: New USB device found, idVendor=090c, idProduct=1000, bcdDevice=11.00
[ 697.470038] usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 697.477180] usb 1-1: Product: USB Flash Disk
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
5.4.102 backported a lot of stuff that our WireGuard backport already
did, in addition to other patches we had, so those patches were
removed from that part of the series. In the process other patches were
refreshed or reworked to account for upstream changes.
This commit involved `update_kernel.sh -v -u 5.4`.
Cc: John Audia <graysky@archlinux.us>
Cc: David Bauer <mail@david-bauer.net>
Cc: Petr Štetiar <ynezz@true.cz>
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
The idea of commit a14f5bb4bd was to use wpad-basic-wolfssl
consistently throughout the whole trunk, so use it here as well.
Fixes: 50fdddae05 ("BPi-M2U kernel modules for onboard WiFi")
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
The rtc-sunxi module only supports Allwinner A10/A20, for Allwinner
A31/h3/h5, use rtc-sun6i instead, which isn't support build as a
kernel module, just put it into default config.
Signed-off-by: AmadeusGhost <amadeus@jmu.edu.cn>
Specification:
- CPU: Allwinner H3, Quad-core Cortex-A7 Up to 1.2GHz
- DDR3 RAM: 512MB/1GB
- Network:
10/100/1000M Ethernet x 1，
10/100M Ethernet x 1
- WiFi: 802.11b/g/n, with SMA antenna interface
- USB Host: Type-A x2
- MicroSD Slot x 1
- MicroUSB: for OTG and power input
- Debug Serial Port: 3Pin 2.54mm pitch pin-header
- LED:
nanopi:red:status
nanopi:green:wan
nanopi:green:lan
- KEY:
reset
- Power Supply: DC 5V/2A
Installation:
- Write the image to SD Card with dd
- Boot NanoPi from the SD Card
Signed-off-by: Jayantajit Gogoi <jayanta.gogoi525@gmail.com>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
This makes it a little easier to figure out which options to choose.
Signed-off-by: Rogan Dawes <rogan@dawes.za.net>
Signed-off-by: CN_SZTL <cnsztl@project-openwrt.eu.org>
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
The file lacks executable permissions, which makes it not being applied
during the first boot.
While at it, drop unneeded include.
Signed-off-by: Piotr Jurkiewicz <piotr.jerzy.jurkiewicz@gmail.com>
[do not touch board name handling, update commit message/title]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
