Sitecom WLR-4100 v1 002 (marked as X4 N300) is a wireless router
Specification:
SoC: MT7620A
RAM: 64 MB DDR2
Flash: MX25L6405D SPI NOR 8 MB
WIFI: 2.4 GHz integrated
Ethernet: 5x 10/100/1000 Mbps QCA8337
USB: 1x 2.0
LEDS: 2x GPIO controlled, 5x switch
Buttons: 1x GPIO controlled
UART: row of 4 unpopulated holes near USB port, starting count from
white triangle on PCB:
VCC 3.3V
GND
TX
RX
baud: 115200, parity: none, flow control: none
Installation
Connect to one of LAN (yellow) ethernet ports,
Open router configuration interface,
Go to Toolbox > Firmware,
Browse for OpenWrt factory image with dlf extension and hit Apply,
Wait few minutes, after the Power LED will stop blinking, the router is
ready for configuration.
Known issues
Some USB 2.0 devices work at full speed mode 1.1 only
MAC addresses
factory partition only contains one (binary) MAC address in 0x4.
u-boot-env contains four (ascii) MAC addresses, of which two appear
to be valid.
factory 0x4 **:**:**:**:b9:84 binary
u-boot-env ethaddr **:**:**:**:b9:84 ascii
u-boot-env wanaddr **:**:**:**:b9:85 ascii
u-boot-env wlanaddr 00:AA:BB:CC:DD:12 ascii
u-boot-env iNICaddr 00:AA:BB:CC:DD:22 ascii
The factory firmware only assigns ethaddr. Thus, we take the
binary value which we can use directly in DTS.
Additional information
OEM firmware shell password is: SitecomSenao
useful for creating backup of original firmware.
There is also another revision of this device (v1 001), based on RT3352 SoC
Signed-off-by: Andrea Poletti <polex73@yahoo.it>
[remove config DT label, convert to nvmem, remove MAC address
setup from u-boot-env, add MAC address info to commit message]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
BananaPi BPi-R2 comes with HDMI and MIPI-DSI. Use dislpay facility in
Linux by add "console=tty1" boot argument.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This fixes a build problem seen after binutils 2.36 is used by default.
Fixes: 3f41153b1c ("toolchain/binutils: switch to version 2.36.1 by default")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
CZ.NIC as part of Turris project released free and open source WTMI
application firmware wtmi_app.bin for all Armada 3720 devices.
This firmware includes additional features like access to Hardware
Random Number Generator of Armada 3720 SoC which original Marvell's
fuse.bin image does not have.
Add a patch which allows to pass the commit id, so the firmware is able
to identify itself, see a04bffeb.
Add a patch to disable linking with gold, since the ARM toolchain
doesn't ship gold.
Cherry-pick the 3 post-release fixes.
Signed-off-by: Andre Heider <a.heider@gmail.com>
02e23db fix compilation errors popped up by GCC-10
7c35173 Merge pull request #29 from pali/sync-a38x-uboot
bb734f5 mv_ddr: a38x: Use SOC_REGS_PHY_BASE for INTER_REGS_BASE
ee1ea84 mv_ddr: a38x: Fix ddr3 compilation
70f3e2e mv_ddr: Fix comment typo
dd960b4 mv_ddr: ddr3: Allow boards to specify CK_DELAY parameter
a87f4f7 mv_ddr: ddr3: only use active chip-selects when tuning ODT
3defcec mv_ddr: a38x: Add support for setting timing in hws_topology_map
Signed-off-by: Andre Heider <a.heider@gmail.com>
2efdb10 wtmi: Fix calculation of UART divider
4247e39 fix: twin die ddr porting guide
8ad7992 sys_init: Add missing newlines in debug mode
4ddea19 avs: Validate VDD value from OTP
c444aeb avs: Fix description for avs value 0x2e
1915b78 tim: Optimize code generated by gettimver.sh and print newline
21f566d tim: Print mv_ddr version and configuration on UART
840b70b tim: Use variable $DDRFILE where possible
c10e6ae tim: Fix waiting for UART TX ready
7bf95cf wtmi: Wait 3ms for the TX on UART to be empty prior resetting TX FIFO
63e8433 wtmi: Add "dirty" suffix to git commit and rebuild sys_init.bin binary when VERSION changes
e949b58 wtmi: During setup clock phase print CPU and DDR speed
10376b5 wtmi: Flush output on UART after the '\n' character
509c647 Makefile: Check that specified DDR_TOPOLOGY option is valid
Signed-off-by: Andre Heider <a.heider@gmail.com>
Revert to using the checked in `tbb_linux` image tool binary since building
it drags in the rather big Crypto++ project.
Cherry-pick the post-release UART fixes.
Switch to AUTORELEASE while at it.
Signed-off-by: Andre Heider <a.heider@gmail.com>
From version 2021.09 U-Boot will fixup Turris Omnia's DTB before
booting, separating U-Boot's environment into separate MTD partition
"u-boot-env" [1].
Check if "u-boot-env" MTD partition exists and set the uci defaults
accordingly.
[1] https://lists.denx.de/pipermail/u-boot/2021-July/455017.html
Signed-off-by: Marek Behún <marek.behun@nic.cz>
As the board name was changed to be identical to the device tree
compatible string (just like for other boards), also reflect that
change for U-Boot.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Add fw_env configuration for the BPi-R2 which is a mediatek/mt7623
devboard which can be booted from SD Card or eMMC.
Auto detect the boot device and add environment accordingly.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
All mediatek boards having fw_env accessible through uboot-envtools
belong to be mt7622 subtarget. Move the file, as subtarget-specific
files are supported for a while now.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* use built-in default environment instead of file in bootfs
* get rid of bootfs alltogether and use uImage.FIT
* auto-detect boot device like original script did
* add support for factory button
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ! Behavior change !
Old behavior: If the Reset button is held down during power-on
do factory reset and try booting recovery from TFTP forever.
If valid recovery is received via TFTP, write it to flash and boot.
New behavior: If the Reset button is held down during power-on
do factory reset, then try TFTP *once*, then try booting on-flash
recovery, then keep trying via TFTP forever until a valid image is
received.
Only if there is no bootable recovery stored on flash, store the
downloaded recovery. Then boot it.
* Set loadaddr to 0x48000000 in order to allow booting images larger
than ~47MB (reported by Oskari Lemmelä). Setting loadaddr to
0x48000000 gives us 384MB on devices with 512MB RAM, which should be
more than enough as a maximum size for uImage.FIT to be loaded.
* Widely unify device-specific default environment in preparation to
auto-generate it from parameters.
* backport upstream commit fixing MBR/DOS partitioning
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Specifications:
- SoC: MT7621AT
- RAM: 256MB
- Flash: 128MB NAND
- Ethernet: 5 Gigabit ports
- WiFi: 2.4G/5G MT7615N
- USB: 1 USB 3.0, 1 USB 2.0
This device is very similar to the EA7300 v1/v2, EA7500 v2, and EA8100 v1.
Installation:
Upload the generated factory image through the factory web interface.
(following part taken from EA7300 v2 commit message:)
This might fail due to the A/B nature of this device. When flashing, OEM
firmware writes over the non-booted partition. If booted from 'A',
flashing over 'B' won't work. To get around this, you should flash the
OEM image over itself. This will then boot the router from 'B' and
allow you to flash OpenWRT without problems.
Reverting to factory firmware:
Hard-reset the router three times to force it to boot from 'B.' This is
where the stock firmware resides. To remove any traces of OpenWRT from
your router simply flash the OEM image at this point.
With thanks to Tom Wizetek (@wizetek) for testing.
Signed-off-by: Tee Hao Wei <angelsl@in04.sg>
In order for the grub2 boot-related code to compile normally, we have
made many adjustments to the compilation parameters. These adjustments
are not necessary for tools-related code. We apply these parameter
adjustments only to the boot-related code.
Signed-off-by: 李国 <uxgood.org@gmail.com>
grub2 boot-related code and tools-related code may require different
compilation parameters. We split them into different variants for
compilation, so that we can accurately pass the required parameters and
avoid causing problems.
Signed-off-by: 李国 <uxgood.org@gmail.com>
The grub2 and grub2-efi packages should only contain boot-related code.
grub-bios-setup is the same as grub-editenv, they are both grub2 tools
and should be placed in a separate package.
Signed-off-by: 李国 <uxgood.org@gmail.com>
[use AUTORELEASE and update to SPDX]
Signed-off-by: Paul Spooren <mail@aparcar.org>
This is only cosmetic, but the next one adding a patch here would
have to do it anyway, and thus will get a smaller diff for review
now.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
