use u-boot-rockchip.bin to copy SPL/TPL/U-Boot to the image.
since binman was used in mainline u-boot for rockchip, we can use
u-boot-rockchip.bin instead of idbloader.img and u-boot.itb.
Reviewed-by: Tianling Shen <cnsztl@immortalwrt.org>
Signed-off-by: FUKAUMI Naoki <naoki@radxa.com>
Link: https://github.com/openwrt/openwrt/pull/15815
Signed-off-by: Robert Marko <robimarko@gmail.com>
Upstream now uses standard ETH LED bindings to configure LED registers.
However, we don't use the r8169 driver for rockchip, so simply remove
this outdated hack.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
This is an automatically generated commit which aids following Kernel patch history,
as git will see the move and copy as a rename thus defeating the purpose.
See: https://lists.openwrt.org/pipermail/openwrt-devel/2023-October/041673.html
for the original discussion.
Signed-off-by: Antonio Flores <antflores627@gmail.com>
This is an automatically generated commit.
When doing `git bisect`, consider `git bisect --skip`.
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Hardware spec:
- Rockchip RK3568 Quad-core ARM Cortex-A55 CPU 2GHz
- GPU Mali-G52 1-Core-2EE OpenGL ES3.2 Vu1kn 1.1 OpenCL 2.0
- Memory2G DDR3 SDRAM (option 4G)
- Storage Onboard 16GB eMMC Flash, Micro SD-Card slot, SATA 3.0 Port,SPI flash
- Network 5 x 10/100/1000 Mbit/s Ethernet MT7531
- Display 1 HDMI port, 2 DSI interface(1 DSI can change to LVDS by software)
- Camera 1 CSI camera interface
- Audio Output HDMI & I2S & Speaker & Headphone
- USB port USB 3.0 PORT (x2), micro USB OTG (x1)
- PCIE 1 mini pcie interface & 1 M.2 key-e interface
- Remote IR Receiver (x1)
- GPIO 40 Pin Header : GPIO (x28) and Power (+5V, +3.3V and GND).
- Switches Reset button, Power button, U-boot button
- LED Power Status
- Power Source 12 volt 2A via DC Power
Installation:
Uncompress the OpenWrt sysupgrade and write image to the SD card using dd (dd if=*.img of=/*)
Boot from the SD card
1-hold down the MaskRom button
2-Connect DC power
3-Wait 5 seconds, release the button.
eMMC Installation:
1-Uncompress the OpenWrt sysupgrade image
2-fash to eMMC
dd if=openwrt-rockchip-armv8-sinovoip_bpi-r2-pro-squashfs-sysupgrade.img of=/dev/mmcblk1
sync
3-remove SD card
reboot
Signed-off-by: Antonio Flores <antflores627@gmail.com>
Rockchip SoCs used to have a random number generator as part of their
crypto device, and support for it has to be added to the corresponding
driver.
Newer Rockchip SoCs like the RK3568 have an independent True Random
Number Generator device. Import pending patchset which adds a driver for
it, include it in Kconfig and enable it in the device tree.
Doing so significantly reduces the time needed to boot devices based on
those SoCs, from about 27 seconds until Ethernet is up and running to
less than 13 seconds with a minimal snapshot image.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
