Backport the upstream kernel fix 525b0858ff to get rid of the kernel
messages:
mvebu-gpio xxxxxx.gpio: IRQ index 3 not found
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Buffalo Linkstation LS421DE comes with a Ricoh RS5C372A real time
clock. This RTC has the INTRA pin connected to the power management
circuit, allowing to wake up the device from the power off state when an
alarm is scheduled.
Add the "wakeup-source" property in the RTC dts node to allow the use
of the alarm.
Example of use, the device is powered off and it comes to life after 5
minutes:
echo $(expr $(date '+%s') + 60 * 5) > /sys/class/rtc/rtc0/wakealarm
poweroff
This feature isn't available in the stock firmware.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
The Buffalo Linkstation LS421DE isn't able to enable the Level 2 cache
(AKA Aurora cache). As of result of this, the throughput is about half of
the expected, e.g when doing network data transfers.
Fix it by adding the broken-idle property in the coherency fabric node.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
With board revision 1.3, SolidRun moved the power LED to the middle of
the board. In old place of power LED a GPIO controllable heartbeat LED
was added. This commit touches only Single Shot variant, because all
have revision 1.3. Some boards could be placed in an enclosure, therefore
the LED18 is enabled by default, since that'll be the only visible
indicator that the board is operating.
Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
This adds DTB to kernel and that way makes it possible to easily boot
initramfs image and also kernel.
The sequence to boot initramfs on Omnia is then just:
env set bootargs earlyprintk console=ttyS0,115200
dhcp 0x1000000 192.168.1.1:openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
bootz 0x1000000
Without this change kernel boot won't proceed and is stuck on "Starting
kernel".
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
[fixed From: to match with SoB:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
Fixup dfa357a3de "mvebu: base-files: Update Turris Omnia U-Boot
environment" which should have included this file as well.
By rebasing the initial patch this file somehow disappeared.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia)
[explain fixup in commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
Move the update procedure from sysupgrade to first boot, which is much
more convenient in the sysupgrade case (otherwise the environment is
always one generation behind).
Check whether we have an old U-Boot release installed, and update the
environment only if necessary.
Some notes on the U-Boot environment:
The first 9 lines are a copy of the default environment of the old U-Boot
release - only modified, to run "distro_bootcmd", in case "mmcboot" fails
to boot the factory OS.
The remaining 16 lines are a backport of the default environment of the
new U-Boot release (shipped with CZ11NIC23). The main entry point is
"distro_bootcmd", which eventually sources boot.scr. This way, we have
a unified boot protocol for all Turris Omnia revisions so far.
This commit also fixes a shortcoming of previous Turris Omnia support:
Users may install OpenWrt with the Turris Omnia in factory state
(i.e. invalid environment store). In that case, neither fw_setenv, nor
U-Boot itself, would import the default environment from the image -
screwing up the rescue system, at least!
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia)
In contrast to the U-Boot version shipped with older versions of Turris
Omnia (CZ11NIC13, CZ11NIC20), the version shipped with Turris Omnia 2019
(CZ11NIC23) relies on the existence of /boot.scr.
Consequently, add a suitable boot script to the sysupgrade image.
Flash instructions for Turris Omnia 2019:
- Download openwrt-...-sysupgrade.img.gz, gunzip it, and copy the resulting
.img file to the root of a USB flash drive (FAT32 or ext2/3/4).
- Enter a rescue shell: Either via 5-LED reset and ssh root@192.168.1.1
on LAN port 4, or via 7-LED reset and the serial console.
- Insert the USB drive and mount it:
mkdir /mnt; mount /dev/sda1 /mnt
- Flash the OpenWrt image to eMMC:
dd if=/mnt/openwrt-...-sysupgrade.img of=/dev/mmcblk0 bs=4096 conv=fsync
- Reboot.
Flash instructions using a temporary "medkit" installation were written for
the older versions of Turris Omnia, and will *not* work on the Turris Omnia
2019.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
This is already done by get_partitions.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[add "redundant" to title, remove declaration of magic variable]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Sort patches according to target/linux/generic/PATCHES. Additionally:
- replace hashes in backported patches with the ones from main Linux tree
- add descriptions to some patches
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
[remove 004-add_sata_disk_activity_trigger.patch separately]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Remove 004-add_sata_disk_activity_trigger.patch, as the trigger is
already added in shared dtsi.
Suggested-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
This patch adds support for Globalscale ESPRESSObin-Ultra. Device uses
the same Armada-3720 SoC with extended hardware support.
- SoC: Armada-3720
- RAM: 1 GB DDR4
- Flash: 4MB SPI NOR (mx25u3235f) + 8 GB eMMC
- Ethernet: Topaz 6341 88e6341 (4x GB LAN + 1x WAN with 30W PoE)
- WiFI: 2x2 802.11ac Wi-Fi marvell (88w8997 PCIe+USB)
- 1x USB 2.0 port
- 1x USB 3.0 port
- 1x microSD slot
- 1x mini-PCIe slot (USB [with nano-sim slot])
- 1x mini-USB debug UART
- 1x RTC Clock and battery
- 1x reset button
- 1x power button
- 4x LED (RGBY)
- Optional 1x M.2 2280 slot
** Installation **
Copy dtb from build_dir to bin/ and run tftpserver there:
$ cp ./build_dir/target-aarch64_cortex-a53_musl/linux-mvebu_cortexa53/
linux-5.4.65/arch/arm64/boot/dts/marvell/armada-3720-espressobin-ultra.dtb
bin/targets/mvebu/cortexa53/
$ in.tftpd -L -s bin/targets/mvebu/cortexa53/
Connect to the device UART via microUSB port on the back side and power on the device.
Power on the device and hit any key to stop the autoboot.
Set serverip (host IP) and ipaddr (any free IP address on the same subnet), e.g:
$ setenv serverip 192.168.1.10 # Host
$ setenv ipaddr 192.168.1.15 # Device
Ping server to confirm network is working:
$ ping $serverip
Using neta@30000 device
host 192.168.1.15 is alive
Tftpboot the firmware:
$ tftpboot $kernel_addr_r openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-initramfs-kernel.bin
$ tftpboot $fdt_addr_r armada-3720-espressobin-ultra.dtb
Set the console and boot the image:
$ setenv bootargs $console
$ booti $kernel_addr_r - $fdt_addr_r
Once the initramfs is booted, transfer openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
to /tmp dir on the device.
Gunzip and dd the image:
$ gunzip /tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img.gz
$ dd if=/tmp/openwrt-mvebu-cortexa53-globalscale_espressobin-ultra-squashfs-sdcard.img of=/dev/mmcblk0 && sync
Reboot the device.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Manually rebased patches:
bcm27xx:
patches-5.4/950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch
bcm53xx:
patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch
layerscape:
patches-5.4/802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
patches-5.4/808-i2c-0002-MLK-10893-i2c-imx-add-irqf_no_suspend.patch
patches-5.4/820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch
Removed since could be reverse-applied by quilt:
mediatek:
patches-5.4/0700-arm-dts-mt7623-add-missing-pause-for-switchport.patch
All modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86_64
Run-tested: ipq806x/R7800, x86_64
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64]
Rebase of 802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
The generic bootscript is tailored around a downstream firmware and
doesn't work on a firmware built from mainline components.
Add a bootscript which:
* sets $console since mainline u-boot doesn't do that
* uses distro boot variables, so OpenWRT can be booted off any supported
device when using a mainline firmware
* sets missing distro boot variables for the downstream firmware
Booting with a downstream firmware is unchanged.
Booting with a mainline firmware now works.
Signed-off-by: Andre Heider <a.heider@gmail.com>
correct oversight on setting regulatory country and mac address of wireless configuration
change method of retrieving mac address
The MAC address for eth0 is rad out of the devinfo partition in some
other initial configuration script already.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
correct device CC oversight
Set the initial wifi configuration like for the other similar Linksys
devices.
Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
This commit contains patches for PCI aardvark driver and relevant DTS
changes for Turris MOX and EspressoBin backported from mainline kernel.
It fixes support for old ATF, various wifi cards, mainly Compex WLE900VX.
Signed-off-by: Pali Rohár <pali@kernel.org>
Similar to how it was already done for other filesystems' *_FS_XATTR
kernel config symbols, also move CONFIG_F2FS_FS_XATTR=y and
CONFIG_F2FS_STAT_FS=y to target/linux/generic.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Extended attributes are required for overlayfs and have hence been long
ago enabled for jffs2, but should be enabled unconditionally for all
other filesystems which may potentially serve as overlayfs' upper
directory. Previously it was inconsistently added in multiple targets.
Add symbols to generic kernel config and remove all *_XATTR symbols
from target configs.
Signed-off-by: Paul Spooren <mail@aparcar.org>
[keep things as they are for squashfs, improve commit message]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Seemingly unneeded based on new upstream code so manually deleted:
platform/820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch
Manually merged:
generic-hack/251-sound_kconfig.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to
GPL-2.0-or-later. Reflect that in the SPDX license headers.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
fdt_addr and kernel_addr variables are getting obsolete in the mainline
u-boot in favor of fdt_addr_r and kernel_addr_r.
By checking if the new variables exist, we can make sure that devices with newer
version of u-boot will work while not breaking support for the existing ones.
Signed-off-by: Vladimir Vid <vladimir.vid@sartura.hr>
Acked-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Manual merged:
hack-5.4
230-openwrt_lzma_options.patch (with Adrian Schmutzler's help)
bcm27xx
950-0283-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch
x86
patches-5.4
011-tune_lzma_options.patch (with Adrian Schmutzler's help)
Remove upstreamed patches in collaboration with Ansuel Smith:
ipq806x
093-1-v5.8-ipq806x-PCI-qcom-Add-missing-ipq806x-clocks-in-PCIe-driver.patch
093-2-v5.8-ipq806x-PCI-qcom-Change-duplicate-PCI-reset-to-phy-reset.patch
093-3-v5.8-ipq806x-PCI-qcom-Add-missing-reset-for-ipq806x.patch
All other modifications made by update_kernel.sh
Build system: x86_64
Run-tested: ipq806x (R7800)
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
